manualshive.com logo in svg

fimotec-fischer 90.0210.61, Operating Instructions Manual, Page: 32 / 46

Share
Download
fimotec-fischer 90.0210.61 Operating Instructions Manual Download Page 32

Operating instructions FS-26E 

 

 

 
 

 

Status as of 10 / 2019 

Page 34

 
 

 

4.14    Factory settings / read/save user backup 

 
Via the control panel, activate the menu item 0old on level 0.  
Change to programming mode (see the control panel and operator code): 
 
 
Start in "Amplitude" root display 
 

 

 

 

 

 

 
To load the factory settings, select the menu item "re". Proceed analogously to saving.  
Your operator code-specific parameters will be reset to the factory settings. 
 

 

 

 

 

 
To restore your backed-up data, select the menu item "

br

". Proceed analogously to saving. 

Your operator code-specific parameters will be loaded. 
 

 

 

 

 

 
To back up your settings, select the menu item 

bs

 and press the 

5

 key. The security query 

sure

 appears. 

Press the 5 key again to save. "

Save

" appears and immediately the selected parameter again. 

Your operator code-specific parameters will be backed up. 
 

 

 

 

 
 

Summary of Contents for 90.0210.61















































Reviews:

No comments