Fike Quadnet Engineering And Commissioning Manual Download Page 32 | Manualshive

Page: 32 / 74

background image

Quadnet Control Panel Engineering and Commissioning Manual

32

4. Disable / Enable 5. Fault Outputs

This function allows the global disablement or enablement of all fault outputs on the system. The
control panel will indicate that disablements are present and a disablement event will be recorded
in the log.

4. Disable / Enable 6. Default to All Enabled

This function enables any device / action that may have been disabled, and all programmed actions
are reinstated. The control panel event log will indicate that all actions have been reinstated.

5. Set Time and Date

This allows the time and date to be adjusted.

6. Test Modes 1. Silent Test

The Silent Test function allows the selection of one or more detection-zones to operate in a ‘silent
one-man walk test mode’. On triggering a device the device LED operates and the event is
recorded in the event log as a test activation, but the sounder does not sound and the control panel
does not show an alarm. After approximately 5 seconds the system will reset the device, and
another may be tested. The control panel event log will indicate that a test mode has been
selected.

6. Test Modes 2. Local Audible Test

The Local Audible Test function allows the selection of one or more detection-zones to operate in a
‘one-man walk test mode with local sound’. On triggering a device the device LED operates, the
sounder within that device operates and the event is recorded into the event log as a test activation,
but the control panel does not show an alarm. After approximately 5 seconds the system will reset
the device, and another may be tested. The control panel event log will indicate that a test mode
has been selected.

6. Test Modes 3. System Test

The System Test function allows the entire system to operate in a simple one-man walk test mode.
On triggering a device the device LED operates and the event is recorded in the event log, all the
assigned sounders operate for 10 seconds and the control panel indicates an alarm. After
approximately 10 second the system will reset the device, and another may be tested. The control
panel event log will indicate that a test mode has been selected.

Please note, with the system test mode, only the sounders assigned to operate from that device will
sound, and any delays will still be present. ie. if a delay of 2 minutes is present, the system will
have been reset before the sounders activate.

«
...
30
31
32
33
34
...
»

Summary of Contents for Quadnet











































































Reviews:

No comments

Related manuals for Quadnet

Brand: Cansec Pages: 45

Brand: Cansec Pages: 43

Brand: Cansec Pages: 32

Brand: Fairchild Pages: 2

Brand: Fairford Pages: 233

Brand: Fantech Pages: 2

Brand: Parker Pages: 28

Brand: Saftronics Pages: 13

Brand: Yamaha Pages: 92

Brand: Partizan Pages: 7

Brand: SYR Pages: 2

Brand: Paradox Pages: 6

Brand: 2gig Technologies Pages: 6

Brand: Scanreco Pages: 10

Brand: Teledyne Pages: 102

Brand: Seneca Pages: 4

GA INDUSTRIES Figures 251-D

Brand: Vag Pages: 6

Brand: KATO VISION Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands