Fike Quadnet Engineering And Commissioning Manual Download Page 28

Page: 28 / 74

Quadnet Control Panel Engineering and Commissioning Manual

Fire Alarm Controls

The main Fire Alarm Controls may be enabled by turning the key switch to the controls enabled position, or
by entering a valid Access code.

System Controls

User

Supervisor

Engineer

A context-driven highlighted-selection menu system is used to navigate the menu system, automatically
prompting you with the relevant options for your Access Level and system status.

The menus may be navigated in one of two ways as required:

1. Use the

DOWN

keys to move the highlighted selection and press

ENTER

to select the

chosen one.

2. Enter the desired option number and press

ENTER

to select it.

Press the

Esc

key to exit to the previous menu.

Delay On/Off

2. Test Display

3. View Logs

4. Disable/Enable

5. Set Time & Date

6. Test Modes

7. Day/Night Mode

8. Find Device

fire alarm controls – turn key to enable controls

silence

alarms

reset

system

sound

alarms

enable controls

silence

buzzer

enter

o_o

ABC

DEF

GHI

JKL

MNO

PQRS

TUV

WXYZ

___

ESC

Delay Override

2. Test Display

View Logs

2. Test Display

3. Disable/Enable

4. Set Time & Date

5. Test Modes

6. Day/Night Mode

7. Engineer Controls

Summary of Contents for Quadnet











































































Search results

Summary of Contents for Quadnet

Reviews:

Related manuals for Quadnet

Brands by name

Popular brands

Fike Quadnet, Engineering And Commissioning Manual

Search results

Summary of Contents for Quadnet

Reviews:

Related manuals for Quadnet

Brands by name

Popular brands