Fike Quadnet Engineering And Commissioning Manual Download Page 20 | Manualshive

Page: 20 / 74

background image

Quadnet Control Panel Engineering and Commissioning Manual

20

USB Port: USB

The Quadnet control panel may be programmed using the Quadnet OSP programming software using a
USB lead to link to a computer. This allows the site specific data to be customised as required.

NOTE:

It is imperative that the correct version of OSP is used to match your version of Quadnet
control panel. The use of an incompatible version may result in incorrect operation of the
control panel. In particular, do not use a V2.xx series OSP with a V3.xx series control
panel and do not use a V3.xx series OSP with a V2.xx series control panel.

Serial Port: SERIAL

SW 1

ON

The Quadnet control panel firmware (control panel operating software stored in external flash memory on
the control panel CIE PCB) may be updated using the Quadnet Firmware programming software using a
serial lead to link to a computer. This allows the control panel software version to be updated on site as
required. To enable the flash upgrade option switch 1 must be in the ON position. During normal operation
switch 1 must be set to OFF.

It is important to ensure that the new version is compatible with your hardware version and with
other software used in the system such as loop cards, PSU and repeaters etc. If not, then all items
would need to be updated.

Note that firmware upgrades are only permitted to be carried out by Fike engineers or trained installation
engineers operating under specific instructions from Fike Technical Support.

Network Ports 1- 2: B, A, SCRN

The network ports allow multiple panels to be connected together, up to a maximum of

4

panels (including

both control panels and repeater panels). The 2 network ports (NET1-2) may be connected in any
sequence between panels. Note Network ports 3 + 4 are not currently used.

Note that although the terminals for the network ports are always fitted on the backplane, they may only be
used if the optional Quadnet Network Card has been fitted onto the control panel main PCB (CIE).

Network Port 1

Terminal

Description

SCRN

Field cable screen connection (Connect only at 1 end)

NW1B

Data B connection for Port 1

NW1A

Data A connection for Port 1

NW1B

ON BOARD PCB

FIELD CONNECTIONS

TO NETWORK PORT OF NEXT CONTROL PANEL

NW1A

B
A

SCREEN

ON BOARD PCB

FIELD CONNECTIONS

USB

PC USB PORT

ON BOARD PCB

FIELD CONNECTIONS

SERIAL

PC SERIAL PORT

«
...
18
19
20
21
22
...
»

Summary of Contents for Quadnet











































































Reviews:

No comments

Related manuals for Quadnet

Brand: Eaton Pages: 16

Brand: Samson Pages: 20

Brand: Panasonic Pages: 31

Brand: Panasonic Pages: 31

Brand: Panasonic Pages: 26

Brand: NAiS Pages: 199

Brand: Panasonic Pages: 38

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 179

Brand: Panasonic Pages: 23

Brand: Panasonic Pages: 30

Brand: Panasonic Pages: 26

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 44

Brand: Panasonic Pages: 20

INDUSTRY PAN9028

Brand: Panasonic Pages: 34

Brand: Daikin Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands