manualshive.com logo in svg

FIC PA-2007, Manual, Page: 23 / 26

Share
Download
FIC PA-2007 Manual Download Page 23

Award BIOS Setup

23

PnP Configuration Setup

Resources Controlled By

If you set at Auto, the BIOS automatically arranges all system resources for
you.  If there are conflicts or you are not satisfy with the configuration,
simply set all the resources listed in the above figure by selecting Manual.
The options are: Auto (default), Manual.
The manual options of IRQ- / DMA- assigned to are: Legacy ISA, PCI/ISA
PnP.

Reset Configuration Data

When enabled, this feature allows the system to clear the last BIOS
configuration data and reset them with the default BIOS configuraton data.
The options are: Enabled, Disabled (default).

PNP OS Installed

If the operating system (OS) you installed supports PnP (Plug-and-Play),
such as Windows 95, please select Yes; otherwise, stay with the default
value, No.
The options are: No (default), Yes.

Assign IRQ For VGA

If your PCI VGA card does not need an IRQ, select Disabled; therefore, an
IRQ can be released for the system use.
The options are: Enabled (Default), Disabled.

Summary of Contents for PA-2007



























Reviews:

No comments