manualshive.com logo in svg

FIC PA-2007, Manual, Page: 18 / 26

Share
Download
FIC PA-2007 Manual Download Page 18

PA-2007 Mainboard Manual

18

Power Management Setup

Power Management

When enabled, allows you to use Power Management features.
The options are: Enabled, Disabled (Default).

PM Control by APM

The option No allows the BIOS to ignore the APM (Advanced Power
Management) specification. Selecting Yes will allow the BIOS wait for
APM's prompt before it enters Doze mode, Standby mode, or Suspend mode.
If the APM is installed, it will prompt the BIOS to set the system into the
power saving mode after all tasks are done.
The options are: Yes (Default), No.

Video Off Option

This feature provides the selections of the video display power saving mode.
The option Suspend - Off allows the video display to go blank if the system
enters Suspend mode. The option All Modes - Off allows the video display
to go blank if the system enters Doze mode or Suspend mode. The option
Always On allows the video display to stay in Standby mode even when the
system enters Doze or Suspend mode.
The options are: Suspend - Off (Default), All Modes - Off, Always On.

Summary of Contents for PA-2007



























Reviews:

No comments