manualshive.com logo in svg

FIC PA-2007, Manual, Page: 15 / 26

Share
Download
FIC PA-2007 Manual Download Page 15

Award BIOS Setup

15

When enabled, allows the system BIOS to utilize the prefetch buffer of the
onboard IDE controller to prefetch the next sequential data of the current
access.
The options are: Enabled (Default), Disabled.

IDE HDD Block Mode

When enabled, allows the system to execute read/write requests to hard disk
in block mode.
The options are: Enabled (Default), Disabled.

IDE Primary Master PIO

Allows you to select first PCI IDE channel of the primary master hard disk
mode or to detect it by the BIOS.
The options are: Auto (Default), Mode 0, Mode 1, Mode 2, Mode 3, Mode
4.

IDE Primary Slave PIO

Allows you to select the first PCI IDE channel of the primary slave hard disk
mode or to detect it by the BIOS.
The options are: Auto (Default), Mode 0, Mode 1, Mode 2, Mode 3, Mode
4.

IDE Secondary Master PIO

Allows you to select first PCI IDE channel of the secondary master hard disk
mode or to detect it by the BIOS.
The options are: Auto (Default), Mode 0, Mode 1, Mode 2, Mode 3, Mode
4.

IDE Secondary Slave PIO

Allows you to select the first PCI IDE channel of the secondary slave hard
disk mode or to detect it by the BIOS.
The options are: Auto (Default), Mode 0, Mode 1, Mode 2, Mode 3, Mode
4.

Onboard FDD Controller

When enabled, the floppy diskkette drive (FDD) controller is activated.
The options are: Enabled (Default), Disabled.

Onboard Serial Port 1

Summary of Contents for PA-2007



























Reviews:

No comments