manualshive.com logo in svg

FIC PA-2007, Manual, Page: 11 / 26

Share
Download
FIC PA-2007 Manual Download Page 11

Award BIOS Setup

11

Boot Sequence

Allows the system BIOS to first try to boot the operating system from the
selected disk drive.
The options are: A, C (Default); C, A; C, CDROM, A; CDROM, C, A.

Swap Floppy Drive

When enabled, allows you to switch the order in which the operating system
accesses the floppy drives during boot up.
The options are: Enabled, Disabled (Default).

Boot Up Floppy Seek

When enabled, assigns the BIOS to perform floppy diskette drive tests by
issuing the time-consuming seek commands.
The options are: Enabled (Default), Disabled.

Boot Up Numlock Status

When set to On, allows the BIOS to automatically enable the Num Lock
Function when the system boots up.
The options are: On (Default), Off.

Port 92H Fast A20G

When enabled, allows the A20G bus line signal generated from the chipset
VT82C586A PC/AT to directly pass to port 92H, instead of the keyboard
controller. It will speed up the system performance.
The options are: Fast (Default), Normal.

Typematic Rate Setting

The term typematic means that when a keyboard key is held down, the
character is repeatedly entered until the key is released. When this item is
enabled, you may change the typematic repeat rate.
The options are: Disabled (Default), Enabled.

Typematic Rate (Chars/Sec)

Sets the rate of a character repeat when the key is held down.
The options are: 6 (Default), 8, 10, 12, 15, 20, 24, 30.

Typematic Delay (Msec)

Sets the delay time before a character is repeated.
The options are: 250 (Default), 500, 750, 1000 millisecond.

Summary of Contents for PA-2007



























Reviews:

No comments