FIC PA-2007 Manual Download Page 1 | Manualshive

Page: 1 / 26

FIC PA-2007 Manual Download Page 1

1

Installation Procedures

The PA-2007 has several user-adjustable jumpers on the board that allow you to
configure your system to suit your requirements. This chapter contains
information on the various jumper settings on your mainboard.

To set up your computer, you should follow these installation steps:

n

Step 1 -

Set system jumpers Read this chapter for jumper settings.

n

Step 2 -

Install RAM modules. Please consult Install RAM modules of the

English manual.

n

Step 3 -

Install the CPU. Read this chapter for jumper settings.

n

Step 4 -

Install expansion cards. Please consult Install expansion cards of

the English manual.

n

Step 5 -

Connect cables and power supply. Please consult Connect cables

and power supply of the English manual.

n

Step 6 -

Set up BIOS features. Please read Chapter Two of this manual.

CAUTION : If you use an electric drill to install this mainboard on your
chassis, please wear a static wrist strap. The recommended torque is from
5.0 to 8.0 kg/cm to avoid damaging the chips’ pins.

Chapter 1

1
2
3
...
»

Summary of Contents for PA-2007



























Reviews:

No comments