Festo YXCR Operating Instructions Manual Download Page 95

Page: 95 / 108

Festo — YXCR — 2021-07b

Installation

Energy chain X-module

Energy chain chambers

Allocation

Customer-specific

Sensor cables, plug sockets with cable

Encoder cables, earthing cable

Motor cables or tubing

Motor cables

Tab. 40: Chamber allocation energy chain X-module EHMX-EGC

Energy chain chambers

Allocation

Encoder cables

Motor cables

Motor cables/sensor cables or tubing

Sensor cables, plug sockets with cable (optional), earthing cable
(included)

Tubing (optional)

Tab. 41: Chamber allocation energy chain X-module EHMX-ELGC

Energy chain Y-module

Energy chain chambers

Allocation

Motor cables or tubing

Encoder cables, earthing cable or plug socket with cable

Plug sockets with cables or customer-specific

Customer-specific

Tab. 42: Chamber allocation energy chain Y-module EHMY -...- EGC (except EHMY-LP-EGC-50/125)

Summary of Contents for YXCR












































































































Search results

Summary of Contents for YXCR

Reviews:

Festo YXCR, Operating Instructions Manual, Page: 95 / 108

Search results

Summary of Contents for YXCR

Reviews: