Festo CP-AM-MEAS Original Operating Instructions Download Page 88

Page: 88 / 94

Message texts and interactive error messages at the HMI

8154245 en

9.2

Interactive error messages

9.2.1

Default operation

Interactive messages are displayed via a pop-up window at HMI
The Pop Up has three buttons.

Example application module output - interactive error message in default mode

Position

Note

Repeat - An attempt is made to run the application again.

Ignore

–

The error status is ignored; the workpiece carrier receives the status code as indicated in the transition

table in the "Initial status" column. The application is no longer executed.

Abort

–

The error status is ignored; the workpiece carrier receives the status code as shown in the input / output

field next to the value displayed. This can be changed in this interactive error message window.

Summary of Contents for CP-AM-MEAS































































































Search results

Summary of Contents for CP-AM-MEAS

Reviews:

Related manuals for CP-AM-MEAS

Brands by name

Popular brands

Festo CP-AM-MEAS, Original Operating Instructions

Search results

Summary of Contents for CP-AM-MEAS

Reviews:

Related manuals for CP-AM-MEAS

Brands by name

Popular brands