Festo CP-AM-MEAS Original Operating Instructions Download Page 24 | Manualshive

Page: 24 / 94

background image

Basic safety instructions

24

© Festo Didactic

8154245 en

4.13

Protective devices

In order to reduce risks, this machine contains guards to prevent access to dangerous areas. These guards
must not be removed or tampered with.

WARNING

•

Damage to the safety window

–

Windows must not be cleaned using aggressive or alcoholic cleaning agents.
Risk of brittleness and breakage!

–

This protective device must be replaced if it shows any signs of damage. Please
contact our Service department to arrange this.

4.13.1

Emergency stop

If a station has an emergency stop button, the emergency stop signal switches off all actuators. An
acknowledgment by the operator is required for a restart, there is no automatic restart.

4.13.2

Additional protective devices

The individual components, such as the power supplies and the controllers, possess built-in safety functions
such as short-circuit protection, overcurrent protection, overvoltage protection and thermal monitoring. If
necessary, consult the instruction manual for the device in question for more information.

«
...
22
23
24
25
26
...
»

Summary of Contents for CP-AM-MEAS































































































Reviews:

No comments

Related manuals for CP-AM-MEAS

Brand: ZOLL Pages: 5

Brand: Accu-Chek Pages: 3

Brand: iBin Pages: 2

Brand: Panasonic Pages: 180

Brand: IFM Pages: 175

Brand: IFM Pages: 5

Brand: Ultimate Healthcare Pages: 2

Brand: Ultimate Healthcare Pages: 40

Brand: Yamaha Pages: 48

Brand: XFit Pages: 16

BlackBox Series

Brand: Nakamichi Pages: 23

Brand: Harken Pages: 4

Brand: A&D Pages: 33

Brand: Y.I.C. TECHNOLOGIES Pages: 6

Tacx Boost Bundle

Brand: Garmin Pages: 12

Brand: ABB Pages: 112

Brand: Lites Pages: 8

Brand: Taylor Pages: 82

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands