Festo CP-AM-MEAS Original Operating Instructions Download Page 48 | Manualshive

Page: 48 / 94

background image

Commissioning

48

© Festo Didactic

8154245 en

D-Sub-interface for analogue signals (option

–

not available at all application modules)

The CP application module produces a analogue output signal. These is put on the analogue terminal (4)
and must be connected with the analogue inputs of the basic module:

•

Connect the analogue terminal (4) of the CP application module with the D-Sub-interface for analogue
signals (6) on the rear board of the basic module CP Lab Conveyor. Therefore use the provided
connecting cable (1) with standard D-Sub plugs: 15-pin, two-rowed.

Electrical connections / illustration similar

Position

Description

1

connecting cable with15-pin standard D-Sub-plugs

2

basic module CP Lab Conveyor: control or decentralized periphery

3

CP application module: I/O terminal (+BG-XD1)

4

CP application module: analogue terminal (+BG-XD2A)

5

connecting cable with a SysLink-plug (SysLink-cable)

6

basic module CP Lab Conveyor: board at the back (+G1-XZ2)

«
...
46
47
48
49
50
...
»

Summary of Contents for CP-AM-MEAS































































































Reviews:

No comments

Related manuals for CP-AM-MEAS

Brand: BACtrack Pages: 13

Brand: TA Instruments Pages: 35

Brand: E-Z DRILL Pages: 12

Brand: e-survey Pages: 54

Brand: E-Pill Pages: 8

XL-7 Command Station

Brand: E-Mu Pages: 22

Brand: dbx Pages: 2

Brand: Eagle Group Pages: 8

Brand: Tascam Pages: 8

Brand: KCI Pages: 2

Brand: KCI Pages: 60

Brand: Landoll Pages: 38

Brand: ABB Pages: 33

Brand: Össur Pages: 16

Exoform Dorsal Night Splint

Brand: Össur Pages: 34

Brand: Garmin Pages: 2

Brand: Daekyung Pages: 15

Brand: Unika Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands