13.Maintain tools with care
Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and
changing accessories. Inspect tool cords periodically
and, if damaged, have repaired by authorized service
facility. Inspect extension cords periodically and
replace if damaged. Keep handles dry, clean and free
from oil and grease.
14.Disconnect tools
When not in use, before servicing, and when
changing accessories such as blades, bits and cutters.
15.Remove adjusting keys and wrenches
Form the habit of checking to see that keys and
adjusting wrenches are removed from tool before
turning it on.
16.Avoid unintentional starting
Don’t carry plugged-in tools with finger on switch.
Be sure switch is off when plugging in.
17.Outdoor use extension cords
When tool is used outdoors, use only extension
cords intended for use outdoors and so marked.
18.Stay alert
Watch what you are doing. Use common sense. Do
not operate tool when you are tired.
19.Check damaged parts
Before further use of the tool, a guard or other part
that is damaged should be carefully checked to
determine that it will operate properly and perform
its intended function. Check for alignment of moving
parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect
its operation. A guard or other part that is damaged
should be properly repaired or replaced by an
authorized service center unless otherwise
indicated elsewhere in this instructions manual.
Have defective switches replaced by an authorized
center. Do not use tool if switch does not turn it on
and off.
20.Warning!
The use of any other accessory or attachment other
than recommended in this operation instructions or
the catalog may present a risk of personal injury.
21.Have your tool repaired by an expert
This electric appliance is in accordance with the
relevant safety rules repairing of electric apliances
may be carried out only by experts otherwise it may
cause considerable danger for the user.
22.Connect the dust extraction device
Whenever there are facilities for fitting a dust
extraction system, make sure it is connected and
used.
BEFORE OPERATING THE MACHINE:
•
Check the following:
Do the voltage of the machine correspond with the
mains voltage
Are the mains lead and the mains plug in a good
condition.
•
Do not use extension cables which are too long. Use
extension cables with a core diameter of 1.5 mm
2
minimal and only when the cable is rolled out
completely.
•
In case of a blockage, switch of the machine
immediately.
•
Always compare the maximum rotation speed of
accesoires with the maximum speed of the
percussion drill.
•
Pull the mainsplug from the socket before you
change a drill or accessory.
WHEN OPERATING THE MACHINE:
•
Check if the switch is placed in the ‘OFF’-position
before you connect the machine to mains.
•
Keep the mains cable away from moving parts of the
machine.
•
First switch off the machine before you move the
machine downwards along your body.
•
Never cover the ventilation slots.
IMMEDIATELY SWITCH OFF THE MACHINE
IN CASE OF:
•
Excessive sparking of the brushes and verticiliosis in
the collector.
•
Malfunction of the mainsplug, -socket or damaged
cables.
•
Broken switch.
•
Smoke or smell caused by scorched insulation.
ELECTRICAL SAFETY
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Keep these instructions in a safe place!
Always check that the power supply corresponds to
the voltage on the rating plate.
Your machine is double insulated in accordance
with EN 50144; therefore no earthwire is required.
Replacing cables or plugs
Immediately throw away old cables or plugs when they
have been replaced by new ones. It is dangerous to insert
the plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable for the
power input of the machine. The minimum conductor
size is 1.5 mm
2
. When using a cable reel always unwind
the reel completely.
4
Ferm
) *)+ + ,+ +
,*,*+
-! % % ! ' .'
.%' %' %
. B
( /#
| (
*
| HSS
5
| HSS
+)+/ 1*,*
. C
% !
.
%2! 3! .
$ ,
# .
• ( , #
.
• !
.
• ( !
. !
.
• 6 , #
.
• ( #
.
•
( #
# #.
•
(
, .
•
7 ,
!
. $
# ! ‘OFF’ ( )
#
+$5:) !.
$+*
*+) *1/,*,+
$+*
. D
• ;
()). 7
(A) ! !
.
*5*$* *+)
• *
, , (B).
)! ,
()).
$+ **
•
!
0 -2500
! 1 0 - 40000
! 2 (E), (A)
#!.
/, , **
)+5
• ;
()).
• ) ())
(>).
• ?! ,
(6)
!.
*$$* */
)+5
• ) ! :
(+) ! “L”.
• + ! :
(+) ! “R”.
*+) * + *
. E
* #
.
• 6 ,
# “”.
• 6 ,
# “(”.
$+*
% !
,
! :
1. %( !% 9#
• ) ! #
! ' ! .
Ferm.
2. %2! . .! .% .
• & #.
.
• C .
!
" .
#
$
.
• & .
Ferm .
Ferm
73
