w
ww
ww
w.
.f
f e
e n
n d
d e
e r
r.
.c
co
om
m
✧
w
ww
ww
w.
. m
m r
r g
g e
e a
a r
r h
h e
e a
a d
d .
.n
ne
et
t
P
P
P
P
a
a
a
a
n
n
n
n
e
e
e
e
ll
ll
C
C
C
C
o
o
o
o
n
n
n
n
tt
tt
rr
rr
o
o
o
o
ll
ll
s
s
s
s
Your new 800 Pro™ bass amplifier delivers world-class
Fender
®
tone and world-standard Fender
®
quality:
• 1200 Watts output power into 2
Ω
, (800 Watts into 4
Ω
)
• 3-BAND SEMI-PARAMETRIC EQUALIZER
• EQ ON/OFF from the front panel or remote footswitch
• EQ GAIN for equal or alternate EQ on/off volume levels
• ROOM BALANCE compensates for dark or bright acoustics
• ENHANCE enhances bass and treble frequencies
• BASS/TREBLE traditional tone controls
• COMPRESSOR provides variable sound smoothing
• Amplifier MUTE allows silent inline instrument tuning with
your tuner plugged into TUNER OUT
• EFFECTS LOOP jacks for connecting your effects device or
auxilliary amplifier
• PASSIVE/ACTIVE switch accomodates a normal– or
high–output bass
• Balanced XLR LINE OUT jack with LEVEL control, GROUND
LIFT and PRE/POST EQ selector for output to sound
reinforcement or recording equipment
• Both Speakon® and 1/4" outputs offer maximum flexibility
Thank you for choosing Fender
Thank you for choosing Fender
®
®
—T
—T
one, T
one, T
radition and Innovation—since 1946
radition and Innovation—since 1946
A. INPUT
- Plug your bass in here.
B. PASSIVE/ACTIVE
- Selects pickup type (sensitivity):
PASSIVE - normal (full input sensitivity)
ACTIVE - pre–amplified (low input sensitivity)
C. GAIN
- Adjusts the preamp signal level. Use together with
MASTER VOLUME {L} to set the overall amplifier
loudness. Watch the
PRE AMP
LEDs to determine the
optimal GAIN setting:
PRE AMP CLIP
- Indicates preamp
clipping
(distortion). Occasional flashing is normal at peak playing
intensities – reduce GAIN if unwanted distortion is heard
while this LED is on.
PRE AMP SIGNAL
- Indicates the presense of
sufficient signal strength. Constant illumination is normal
at moderate playing intensities – increase GAIN and/or
instrument volume if this LED is off or only flashing.
D. ROOM BALANCE
- Rotate clockwise for treble emphasis
to compensate for soft acoustic surfaces (carpet/drapes).
Rotate counter–clockwise for bass emphasis to
compensate for hard acoustic surfaces (cement/tile).
E. ENHANCE
- Boosts low and high frequencies.
OFF - Useful for finger–style bass playing
ON - Useful for slap–style/deep–tone bass playing
F. BASS/TREBLE
- Adjusts tone in low/high frequency
bands respectively.
G. SEMI-PARAMETRIC EQUALIZER -
Adjusts
tone in three variable frequency bands. Each
FREQ
knob selects the center of frequency
range that the
LEVEL
knob below adjusts.
NOTE: The EQ has no effect when all
LEVEL
knobs are set to “0.”
H. EQ GAIN
- Adjusts the signal level of the semi-parametric
equalizer circuit when active (
EQ ON). Useful for
setting a balance between EQ on and off volume levels.
I.
EQ ON/OFF
- Switches the semi-parametric equalizer
on/off as indicated by the LED.
J. COMPRESSOR
- Compresses the dynamic range of the
signal to smooth volume peaks and increase sustain.
Rotate fully counter-clockwise to disable the compressor.
K. MUTE
- Disables all amplifier outputs except for TUNER
OUT. LED flashes when MUTE is active.
L. MASTER VOLUME
- Adjusts overall amplifier loudness in
conjunction with GAIN {C}. Watch the
PWR AMP
LED to
determine the optimal MASTER VOLUME setting:
PWR AMP CLIP
- Indicates power amp
clipping
(distortion). Occasional flashing is normal at peak playing
intensities. Reduce MASTER VOLUME if unwanted
distortion is heard while this LED is on.
M. POWER
- Switches the unit on/off as indicated by the LED.
6
F
F
F
F
e
e
e
e
n
n
n
n
d
d
d
d
e
e
e
e
rr
rr
®
8
8
8
8
0
0
0
0
0
0
0
0
P
P
P
P
rr
rr
o
o
o
o
A
A
A
A
m
m
m
m
p
p
p
p
ll
ll
ii
ii
ff
ff
ii
ii
e
e
e
e
rr
rr
PLEASE NOTE: Your 800 Pro is shipped with adhesive rubber feet for non-rack mount applications. Remove feet
prior to rack mounting.
