4
5
CAPABILITIES
- The machine is for indoor use only. Plug the machine into an easily accessible socket.
- To prevent electrical shock - do not use the appliance close to water, do not spill water on to the appliance, power cord or wall socket.
DO
ensure the machine is on a stable surface.
DO
test laminate scrap sheets and set the machine before final laminations.
DO
remove staples and other metal articles prior to laminating.
DO
keep the machine away from heat and water sources.
DO
turn off the machine after each use.
DO
unplug the machine when not in use for an extended period.
DO
use pouches designed for use at the appropriate settings.
DO
keep away from pets, while in use.
DO
ensure self-adhesive pouches are only used with the cold setting.
DO NOT
leave the power cord in contact with hot surfaces.
DO NOT
leave power cord hanging from cupboards or shelves.
DO NOT
use appliance if the power cord is damaged.
DO NOT
attempt to open or otherwise repair the machine.
DO NOT
exceed the machines quoted performance.
DO NOT
allow children to use this machine without adult supervision.
DO NOT
laminate sharp or metal objects (eg: staples, paper clips).
DO NOT
laminate heat-sensitive documents (eg: tickets, ultrasounds etc) on hot settings.
DO NOT
laminate with self-adhesive pouches on hot settings.
DO NOT
laminate an empty pouch.
IMPORTANT SAFETY INSTRUCTIONS - KEEP FOR FUTURE USE
LAMINATOR CONTROLS
A
On / off switch
B
Laminator feed sensor
C
Pouch selection buttons (
, 80mic, 100mic, 125mic)
D
Release lever (
)
E
Pouch / document entry slot
F
Entry support shelf
G
Pouch / document exit
Lamination Feed Sensor
When the machine senses a pouch has been mis-fed
and
has not gone com-
pletely through the machine in a normal operating time, the Lamination Feed
Sensor LED will blink. Use the release lever located at the rear of the machine to
remove the laminate. A beep will sound if a pouch is left on the exit tray to alert
the user to remove the pouch.
Auto Shut Off
If the machine is not active for 30 minutes, the Auto Shut Off function will place
the machine into standby mode. All LEDs will be dimly blinking. To operate the
machine, press any button or cycle the power switch.
‘Release’ function
To remove or re-align a pouch during lamination, activate the release lever
located at the rear of the machine. The pouch can only be removed from the
entry slot when the lever is activated.
t
For best results, use Fellowes ® brand pouches:
Enhance 80, Impress 100, Enhance 80 - Cold Pouches.
t
For self-adhesive (cold pouches) only use the cold setting.
t
This machine does not need a carrier to laminate. It is a carrier-free mechanism.
t
Always put the item to be laminated into the appropriate sized pouch.
t
Always test laminate with a similar size and thickness before final process.
t
Prepare pouch and item for lamination. Place item within pouch centred and
touching the leading sealed edge. Ensure the pouch is not too large for the item.
t
If required, trim excess material from around the item after lamination and
cooling.
t
When working with different pouch thickness’ (temperature settings) it is recom-
mended to first start with the thinnest pouches.
FEATURES & TIPS
Performance
Format
A3 or A4
Entry width
A3 = 318mm
A4 = 240mm
Pouch thickness (min)
75 microns (per side)
Pouch thickness (max)
125 microns (per side)
Warm up time (estimate)
1 minute
Cool down time
60-90 minutes
Lamination speed (+/- 5%)
approx. 30cm/min (fixed speed)
Number of rollers
2
Ready indication
Light & beep
Release lever
Yes
Clear Path / Anti-jam engine
Yes
Technical Data
Voltage / Frequency / Current(Amps)
A3 = 220-240V AC, 50/60Hz, 3.4A
A4 = 220-240V AC, 50/60Hz, 3.4A
Wattage
A3 = 750 Watts
A4 = 750 Watts
Dimensions (HxWxD)
A3 = 105 mm x 532 mm x 146 mm
A4 = 105 mm x 436 mm x 139.2 mm
Net weight
A3 = 2,3 kg
A4 = 1,8 kg
Max document thickness
(laminating capacity)
0.024” / 0.6mm
ENGLISH
E
Let our experts help you with a solution.
Customer Service...
www.fellowes.com
Always call Fellowes before contacting your place of purchase, see the rear cover for contact details.
NEED HELP?
Switch the power on (located at the rear of the machine).
The control panel buttons will flash once as part of a check light system to ensure
proper function.
The machine defaults to the 80mic hot setting. For 100mic, 125mic or cold
laminating press the corresponding pouch selection buttons.
When the machine is ready, a beep will sound and temperature setting button will
stop flashing and remain on.
Place the document into the open pouch. Ensure the document is centered against
the sealed edge. Use the appropriate pouch size for the document.
Ensure the pouch enters the machine sealed edge first. Keep the pouch straight
and central within the slot, not on an angle. Use the entry markings as a guide.
Upon exit, the laminated pouch may be hot and soft. For the best quality and to
prevent jamming remove the pouch immediately. Place the pouch on to a flat
surface to cool. Take care when handling a hot pouch. Always remove laminate
pouch before starting next laminate.
To release a pouch during lamination activate the release lever located at the
rear of the machine. Gently pull pouch out of machine.
4.
5.
6.
7.
8.
9.
10.
11.
Ensure the machine is on a stable surface.
Check there is enough clear space (min 50cm) behind the machine to allow
items to pass through freely.
Plug the machine into an easily accessible main socket.
1.
2.
3.
SETTING UP THE LAMINATOR
HOW TO LAMINATE
Switch off the machine at the wall. Allow the machine to cool. The outside of the machine can be cleaned with a damp cloth. Do not use solvents or flammable materials to
polish the machine. Cleaning sheets can be used with the machine. When the machine is warm – run the sheets through the machine to clean any residue off the rollers. For
optimum performance, it is recommended that cleaning sheets are used with the machine regularly. (Cleaning sheet order codes #5320601)
Problem
Possible cause
Solution
No control panel illumination
Machine not switched on
Switch on machine at rear next to plug inlet and at the wall socket
Lamination Feed Sensor LED is blinking
Laminate was mis-fed
Hold down the release lever and remove the item by hand
All LEDS are dimly blinking
Laminator has gone in to Auto Shut Off
mode
Press any button or cycle the power switch to re-start the machine
Pouch does not completely seal the item
Item may be too thick to laminate
Check pass through thickness is correctly selected and pass through again
Temperature setting may be incorrect
Check pouch thickness is correctly selected and pass through again
Pouch has waves or bubbles
Temperature setting may be incorrect
Check pouch thickness is correctly selected and pass through again
Pouch is lost in the machine
Pouch is jammed
Operate the release lever and pull out the item by hand
Jamming
Pouch was used ‘open end’ first
Pouch was not centered on entry
Pouch was not straight upon entry
Empty pouch was used
Pouch is damaged after lamination
Damaged rollers or adhesive on rollers
Pass cleaning sheets through the machine to test and clean rollers
TROUBLESHOOTING
STORAGE & CLEANING
Saturn3i_A4_A3_407945_RevB_22L_111314.indd 4-5
11/14/14 11:22 AM
