Do not route iSteam, iTempo/Plus, iTempo,
HomeWizard or iGenie control wiring inside conduit
together with power lines or close to hot water or steam
piping. Doing so may result in an inoperative or hazardous
installation.
Do Not alter or modify any MrSteam prod-
uct. Doing so may result in an inoperable or hazardous
installation and will void the warranty
IMPORTANT NOTES:
1. Turn power to the steam generator OFF before con-
necting the control to the generator. Failure to turn the
power off will result in an inoperable control.
2. Do not operate iSteam, iTempo/Plus, iTempo,
HomeWizard or iGenie controls with other than a
MrSteam iSteam or iTempo compatible steam genera-
tor. MrSteam steam generators with serial numbers
lower than 900000, or any other brand of steam gener-
ator are not to be operated with iTempo controls.
Doing so may result in an inoperative or hazardous
installation. If iSteam is used with a generator having
serial number less than 1174000, contact MrSteam
technical support for an upgraded PC board.
3. This document contains important safety, operation and
maintenance information. Leave this document with
management. Do not discard this document.
4. Discontinue use of the steam generator or control if the
steam generator is damaged or otherwise not function-
ing properly. Operating a damaged steam generator
may result in an inoperative or hazardous installation
16
mr
.
steam
®
C L U B T H E R A P Y
Controls
_________________________________________________________________________________________
Control Rough In
Refer to Installation Instructions for the specific control
IMPORTANT NOTE:
The control cables should be run in dedicated 1" conduit to facilitate installation and service.
1. Determine the desired installation location of the
control. The iSteam
®
, iTempo
™
and iTempo/Plus
™
controls are designed to be installed inside or out-
side the steam room as a matter of personal prefer-
ence. If the control is installed inside the steam
room the control must be located:
2. 4 -5 feet above the floor near the bather seating area
3. The control features an integral temperature sensor.
Locate the control in a location representative of the
desired steambathing temperatures.
Do not locate the control above or near the steam
head or direct steam emissions.
4. on a vertical wall
The control cable length is 30 feet. Insure that the
control and/or steam generator are located according-
ly. An optional 60 foot cable is available, PN 103990-60 for
iTempo and PN 104117-60 for iSteam. Contact a MrSteam
technical service representative if a 60 foot cable is required.
IMPORTANT NOTE:
If the control is installed outside the
steamroom a Remote Temperature Probe Part Number MSTS
must be installed inside the steam room, depending on the
control. Insure MrSteam steam generator is iSteam or iTempo
compatible and has a serial number 900000 or higher. If
iSteam is used with a generator having serial number less than
1174000, contact MrSteam technical support for an upgraded
PC board.
See instructions for the MSTS Temperature Probe (located in
the Control Installation Manual related to your specific control
package) before rough-in or installation of control.
Before Installing
Turn power to the steam generator OFF before connecting the
control to the generator. Failure to turn the power off will result in
an inoperable control.
To avoid unintentional steambath operation,
do not locate the control where other controls, accessories,
shower heads, valves, body sprays or similar within the show-
er could cause confusion or interfere with the MrSteam con-
trol’s intended use and function.
Do not use any iSteam
®
, iTempo/Plus
™
,
iTempo
™
, HomeWizard
™
or iGenie
®
controls without reading
and understanding its own manual and the MrSteam steam
generator Installation and Operation Manual. Failure to read
and understand these instructions may result in an inopera-
tive or hazardous installation.
The warning placard located in the documenta-
tion envelope must be read and permanently affixed in a con-
spicuous location near the steam room. Failure to read and affix
this warning placard in a conspicuous location may result in seri-
ous injury or death.
Install the iSteam, iTempo or iTempo/Plus controls according
to installation instructions. Failure to install according to
instructions will result in an inoperative control or hazardous
overheating or inadequate heating of the steam room.
If an iSteam, iTempo or iTempo/Plus control is installed out-
side the steam room a Remote Temperature Probe (PN
MSTS) must be installed inside the steam room per installa-
tion instructions supplied with the Remote Temperature
Probe. Failure to install according to instructions will result in
an inoperative control and overheating of the steam room.
Control Installation
Refer to Control Manual for specific installation requirements
