Federal Signal Corporation Informer I-HIOW Installation And Operation Manual Download Page 3

Page: 3 / 30

Informer Wall Mount Series

Contents

Safety Message ........................................................................................................................ 1

Read and Understand ............................................................................................................ 1

Installation Considerations ...................................................................................................... 1

Notices ................................................................................................................................... 2

Servicing ................................................................................................................................ 2

Symbol Definition ................................................................................................................ 2

General Description ................................................................................................................. 3

Introduction to the Informer TAR ............................................................................................. 3

Features ................................................................................................................................. 4

Optional Features ................................................................................................................... 4

Informer Wall Mount Main Components .................................................................................. 5

Input/Output Definitions .......................................................................................................... 6

Specifications........................................................................................................................... 7

Installation Instructions ..........................................................................................................10

Determine a Suitable Location ...............................................................................................10

Wall Mounting ........................................................................................................................11

Recessed Mounting ...............................................................................................................12

Input/Output Connections ......................................................................................................13

Wiring the Device ..................................................................................................................13

Operating Instructions ............................................................................................................16

General Information ...............................................................................................................16

Power Supply ........................................................................................................................16

LED Indicators .......................................................................................................................17

Keypad ..................................................................................................................................17

Adjusting the Volume .........................................................................................................17

Receiving an Alert Message ..................................................................................................18

Receiving a Test Message ....................................................................................................19

Tone-Alert Radio Failure .......................................................................................................19

Dual Relay and 600 ohm Audio Output..................................................................................19

Relay Outputs ....................................................................................................................19

600 Ohm Audio Output ......................................................................................................19

Monitoring Weather (NOAA Weather Radio and Channel Selection) .....................................20

Testing .....................................................................................................................................21

Training....................................................................................................................................21

Using the Battery Switch .......................................................................................................21

Summary of Contents for Informer I-HIOW































Search results

Summary of Contents for Informer I-HIOW

Reviews:

Related manuals for Informer I-HIOW

Brands by name

Popular brands

Federal Signal Corporation Informer I-HIOW, Installation And Operation Manual

Search results

Summary of Contents for Informer I-HIOW

Reviews:

Related manuals for Informer I-HIOW

Brands by name

Popular brands