background image

12

  

  

Installation

Informer-PA for Public Address Interface (Model I-IP2 Series C) 

Federal Signal www.fedsig.com

Figure 4 Wall Mount Dimensions

18.98

6.06"

1.70"

18.28

1.25"

1.71"

14.18

Connect the Informer-PA to the LAN using CAT5 cable. If the Wired Ethernet has PoE, no 

other power connection is required.
If PoE is not available, run the supplied external AC/DC power supply against the wall and 

plugged into a 120 Vac, 60 Hz outlet. Plug the low-voltage end of the cord into the power 

jack located at the rear of the Informer-PA. Route the cord to ensure it is protected against 

walking on, tripping over, or pinching the cord.

Memory Card Removal and Installation

The microSD card stores voice and tone messages. 
To remove the card:
1.  Remove the top of the Informer.
2.  Find the microSD card for each of the Informer-PA’s PCB inside the I-IP2.
3.  The PCB may require removal from the enclosure for the microSD card to be 

removed.

4.  Gently push the card into the slot. The card can then be removed.
To install the card:
1.  Insert and gently push the card until it latches into place. Replace the PCB if removed.
2.  Replace cover and tighten screws.

Summary of Contents for C Series

















Reviews: