FAZUA RIDE 50 TRAIL/STREET Original Instructions Manual Download Page 62

Page: 62 / 68

Freigabeversion

US-English | Original instructions

DANGER

Risk of electric shock!

Improper handling of the CHARGER or incorrect mains connection may

expose you and others to the risk of electric shock.

►

Observe the instructions in in section “CHARGER”.

You can either leave the BATTERY in the DRIVEPACK during charging or remove it

from the DRIVEPACK and charge it separately. The charging process can also be

interrupted at any time.
You cannot charge the BATTERY if the temperature is outside the permissible charging

temperature (14 °F to 140 °F (-10 °C to +60 °C)).. This is not possible even if the

BATTERY is connected to the CHARGER.
Charging is only possible again when the permissible charging temperature has

been reached.

→

Fully charge the BATTERY prior to initial operation so that you can use the full

capacity of the BATTERY.

27.7.1 Connecting the BATTERY to the CHARGER

1. Open the cover flap to access the charging socket

[D.3]

D.3

2. Insert the charging plug

[E.3]

into the charging socket on the BATTERY. Since

the charging plug is magnetically coded, it can only be plugged in in the

intended position.

Summary of Contents for RIDE 50 TRAIL/STREET




































































Search results

Summary of Contents for RIDE 50 TRAIL/STREET

Reviews:

Related manuals for RIDE 50 TRAIL/STREET

Brands by name

Popular brands

FAZUA RIDE 50 TRAIL/STREET, Original Instructions Manual

Search results

Summary of Contents for RIDE 50 TRAIL/STREET

Reviews:

Related manuals for RIDE 50 TRAIL/STREET

Brands by name

Popular brands