FAZUA RIDE 50 TRAIL/STREET Original Instructions Manual Download Page 32

Page: 32 / 68

Freigabeversion

US-English | Original instructions

7.2 Cleaning and maintaining components

CAUTION

Risk of injury!

If the drive system is set in motion while you are handling it, you may

trap your fingers or otherwise injure yourself.

►

Remove the DRIVEPACK from the e-bike when cleaning the e-bike

or the drive system components.

NOTE

Risk of damage!

Improper cleaning may damage the drive system or individual

components.

►

Never immerse the drive system components in water or other

liquids for cleaning.

►

Do not use aggressive cleaning agents for cleaning.

►

Do not use sharp, angular or metallic cleaning objects when

cleaning.

►

Never clean the drive system components with a hard water jet or

a high-pressure cleaner.

→

Always keep all components of the e-bike and the drive system in a clean condi-

tion.

→

Clean the components gently with a cloth or soft brush.

→

Wipe all surfaces and components dry after cleaning.

→

Pay particular attention to the contacts and interfaces between BATTERY and

DRIVEPACK and between DRIVEPACK and BOTTOM BRACKET: The interfaces must

not be soiled or contaminated and must be completely dried before inserting

the components to avoid damage.

→

Clean the cooling unit on the DRIVEPACK regularly.
Do not wait until the cooling unit is visibly or heavily soiled before cleaning it!

Summary of Contents for RIDE 50 TRAIL/STREET




































































Search results

Summary of Contents for RIDE 50 TRAIL/STREET

Reviews:

Related manuals for RIDE 50 TRAIL/STREET

Brands by name

Popular brands

FAZUA RIDE 50 TRAIL/STREET, Original Instructions Manual

Search results

Summary of Contents for RIDE 50 TRAIL/STREET

Reviews:

Related manuals for RIDE 50 TRAIL/STREET

Brands by name

Popular brands