FAZUA RIDE 50 TRAIL/STREET Original Instructions Manual Download Page 35

Page: 35 / 68

Freigabeversion

Original instructions | US-English

TROUBLESHOOTING” OVERVIEW TABLE

Problem

possible Reason / Solution

The upper LED on

the REMOTE lights

up/flashes yellow.

There may be a poor connection between the speed sensor

and the BOTTOM BRACKET.

→

Check the position of the spoke magnet. If you cannot

find any faults, contact a FAZUA certified partner.

The white LEDs on

the REMOTE flash.

Software update

→

After a new firmware update, the REMOTE is updated

automatically. In this case, please wait and do not

switch off the REMOTE until the LEDs stop flashing.

The REMOTE cannot

be switched on.

The BATTERY is flat or has switched off due to a longer rest

period (standstill).

→

Try turning on the BATTERY at the on/off button.

→

Charge the BATTERY if necessary.

The interface between the BATTERY and the DRIVEPACK

may be dirty.

→

Clean the interface between the BATTERY and DRIVE-

PACK.

The BATTERY cannot

be inserted into the

DRIVEPACK or does

not engage in the

battery holder.

The interface between the BATTERY and the DRIVEPACK

may be dirty.

→

Clean the interface between the BATTERY and

DRIVEPACK.

The pedal support

suddenly fails

during the ride.

BMS protection function

→

Turn off the BATTERY by pressing the on/off button for

3 seconds and then turn it on again.

Summary of Contents for RIDE 50 TRAIL/STREET




































































Search results

Summary of Contents for RIDE 50 TRAIL/STREET

Reviews:

Related manuals for RIDE 50 TRAIL/STREET

Brands by name

Popular brands

FAZUA RIDE 50 TRAIL/STREET, Original Instructions Manual

Search results

Summary of Contents for RIDE 50 TRAIL/STREET

Reviews:

Related manuals for RIDE 50 TRAIL/STREET

Brands by name

Popular brands