Fayat Group DYNAPAC CA2800, Instruction Manual

Page: 17 / 170

Safety - General instructions
4812159001_I.pdf 2019-11-05
Safety - General instructions
(Also read the safety manual)
• The operator must be familiar with the contents of the OPERATION section
before starting the roller. • The operator must be familiar with the contents of the OPERATION section
before starting the roller.
• Ensure that all instructions in the MAINTENANCE section are followed. • Ensure that all instructions in the MAINTENANCE section are followed.
• Only the operator is allowed to be on the roller. Remain seated at all times
when operating the roller. • Only the operator is allowed to be on the roller. Remain seated at all times
when operating the roller.
•
Never use the roller if it is in need of adjustment or repair.
•
Never use the roller if it is in need of adjustment or repair.
•
Only ascend and descend the roller when it is stationary. Use the intended
footsteps, grips and rails. Always use the three-point grip (both feet and one
hand, or one foot and both hands) when ascending or descending the
machine. Never jump down from the machine.
•
Only ascend and descend the roller when it is stationary. Use the intended
footsteps, grips and rails. Always use the three-point grip (both feet and one
hand, or one foot and both hands) when ascending or descending the
machine. Never jump down from the machine.
• Dynapac always recommends mounted ROPS (Roll Over Protective
Structure), or a ROPS-approved cab and seat belt usage. • Dynapac always recommends mounted ROPS (Roll Over Protective
Structure), or a ROPS-approved cab and seat belt usage.
•
Drive slowly in sharp bends.
•
Drive slowly in sharp bends.
•
Avoid driving across slopes. Drive straight up or straight down the slope.
•
Avoid driving across slopes. Drive straight up or straight down the slope.
•
Never operate with roller outside the edge, if the substrate does not have full
bearing strength or is close to a slope. Avoid operating close to edges and
ditches and the like as well as on poor ground conditions that jeopardizes
the bearing strength and capacity to support the roller.
•
Never operate with roller outside the edge, if the substrate does not have full
bearing strength or is close to a slope. Avoid operating close to edges and
ditches and the like as well as on poor ground conditions that jeopardizes
the bearing strength and capacity to support the roller.
• Make sure that there are no obstacles in the direction of travel, on the
ground, in front of or behind the roller, or overhead. • Make sure that there are no obstacles in the direction of travel, on the
ground, in front of or behind the roller, or overhead.
•
Drive particularly carefully on uneven ground.
•
Drive particularly carefully on uneven ground.
•
Keep the roller clean. Clean any dirt or grease that accumulates on the
operator platform immediately. Keep all signs and decals clean and legible.
•
Keep the roller clean. Clean any dirt or grease that accumulates on the
operator platform immediately. Keep all signs and decals clean and legible.
• Safety measures before refueling:
- Stop the engine
- Do not smoke.
- No naked flames in the vicinity of the roller.
- Earth the filling equipment nozzle to the tank opening to avoid sparks. • Safety measures before refueling:
- Stop the engine
- Do not smoke.
- No naked flames in the vicinity of the roller.
- Earth the filling equipment nozzle to the tank opening to avoid sparks.
• Before repairs or service:
- Chock the drums/wheels.
- Lock the articulation if necessary.
- Place blocks under overhanging equipment, such as strike-off blade and
chip spreader. • Before repairs or service:
- Chock the drums/wheels.
- Lock the articulation if necessary.
- Place blocks under overhanging equipment, such as strike-off blade and
chip spreader.
• Hearing protection is recommended if the noise level exceeds 80 dB(A). The
noise level can vary depending on the equipment on the machine and the
surface the machine is being used on. • Hearing protection is recommended if the noise level exceeds 80 dB(A). The
noise level can vary depending on the equipment on the machine and the
surface the machine is being used on.
5