background image

 
 
 
 

  
 
 
1. 

ALWAYS

 wear safety glasses when operating. 

 
2. 

KEEP FINGERS AWAY

 from cutting blades at all times. 

 
3. 

TURN THE SELECTOR

 on the side of the machine from 

BEND

 to 

CUT.

 

 
4. 

POSITION

 bar or bars between cutting blades.  Bar must rest on the bottom of the cutter opening 

as shown.  

  

 

 

 
5.  ADJUST THE BAR SUPPORT

 on the right side of the cutter so the bar is held perpendicular to 

the  cutting  blades.    Press  the  foot  pedal  until  the  cut  is  made  and  then  release  the  pedal.   

DO 

NOT

 cut ve

ry short pieces (3” or shorter) as they could fly out and cause an accident. If you must 

cut  short  pieces,  you  must  come  up  with  a  way  to  contain  the  cut  pieces  to  prevent  them  from 
flying out and injuring someone. 

 
 

5. 

CUTTING BLADES

 have 4 cutting edges.  When one set of edges is worn, simply remove blade 

securing bolts and rotate to the next sharp edge. To access the blade securing bolts for the blade 
that  moves,  simply  turn  on  the  machine  and  make  sure  Cut/Bend  lever  is  in  the  CUT  position. 
Press  the foot  pedal  and  when  the  ram  has  extended about  ¾  of  the  way  out,  flip  off  the  on/off 
switch and turn the motor off. The ram will stay in the extended position until the machine is turned 
back  on  again.  Now  you  can  access  the  blade  securing  bolts  to  rotate  or  exchange  this  blade. 
Carefully  grind  mushroomed  edges  flat  if  they  prevent  proper  seating  of  the  blade  in  its  new 
position.  

DO NOT

 attempt to re-sharpen worn edges as you will destroy the temper (hardening) 

properties of the blade and it will be ruined. 

 
 

    

DO NOT continue to cut with worn blades as damage to the machine or SERIOUS 
INJURY COULD RESULT. 

 

 
DO  NOT  CUT  VERY  SHORT  PIECES,    They  can  fly  out  and  cause  an  accident. 
SERIOUS INJURY COULD RESULT. 
 

 
 
 

OPERATION OF OPTIONAL 

CUTTER

 

Summary of Contents for 19547








































Reviews: