FarmTek Growers Supply GrowSpan Round Pro Instruction Manual Download Page 15

Page: 15 / 51

GROWSPAN

™

ROUND PRO GREENHOUSES AND SYSTEMS

Revision date: 01.03.19

CABLE PLACEMENT

The diagram and inserts below identify the placement and

proper way to attach the cable assemblies to the building.

Do not tighten the cables until the frame is properly and

securely anchored to the site as described in the Must

Read document.

NOTE:

The positions of the cable assemblies are identical for the opposite

side and the remaining end of the building that are not shown.

Consult the

Side Profile Diagram in the Quick Start section for rafter spacing and cable

locations

View is from inside

the shelter.

Apply duct tape over

cables on end rafters

to protect the main

cover.

Carriage bolt runs through rafter

and top center purlin on the 6th

at each end.

Attach the band clamp (103856) above the lowest

pipe strap (QH1070) on the end rafters only. Once

the cable is attached and the clamp is tightened,

secure the clamp to the rafter using a Tek screw.

View is from

inside the

shelter.

103856

QH1070

ATTENTION:

Install

a carriage bolt in this

location at both ends of

the shelter.

Drill through the rafter

and purlin to install the

bolt.

Top, Center

Purlin

Top, Center

Purlin

5" Carriage Bolt

Summary of Contents for Growers Supply GrowSpan Round Pro




















































Search results

Summary of Contents for Growers Supply GrowSpan Round Pro

Reviews:

Related manuals for Growers Supply GrowSpan Round Pro

Brands by name

Popular brands

FarmTek Growers Supply GrowSpan Round Pro, Instruction Manual

Search results

Summary of Contents for Growers Supply GrowSpan Round Pro

Reviews:

Related manuals for Growers Supply GrowSpan Round Pro

Brands by name

Popular brands