manualshive.com logo in svg

FarmTek Growers Supply GrowSpan Round Pro, Instruction Manual

The FarmTek Growers Supply GrowSpan Round Pro is an exceptional greenhouse solution for avid gardeners. For comprehensive instructions on assembling and utilizing this remarkable product, users can conveniently download the free Instruction Manual from our website. Create an optimal growing environment effortlessly with this easy-to-use resource.

Share
Download
background image

GROWSPAN

™

 ROUND PRO GREENHOUSES AND SYSTEMS

10

Revision date: 01.03.19

INTERIOR RAFTER ASSEMBLIES

Gather the parts:
•  Rafter pipe (#37R23S1D)
•  Rafter pipe (#38R23S1) 
•  Rafter pipe (#38R23P2) 
•  Rafter foot (#104302) 
•  Tek screws (#FA4482B) 
•  FAG363B 3/8" x 3" bolt and FALB04B 3/8" nut

Assemble Interior Rafters With Attached Ratchets
1.  Connect the pipes as shown below. Each rafter assembly consists of five (5) pipes: 2 (#37R23S1D), 2 (#38R23S1), 

and 1 (#38R23P2). Each #37R23S1D pipe includes 

one drilled hole near the bottom

 used to connect the rafter foot. 

2.  With the rafter pipes assembled on the ground, secure each pipe joint using one self-tapping Tek screw (FA4482). 

Position screws so they will not interfere with the cover once it is installed.

3.  Attach a rafter foot to each leg of the rafter using a 3/8" x 3" bolt and 3/8" nut. Position the bolt head to the outside of 

the rafter to prevent cover damage when it is installed.

Diagram shows position of the 

cross connector. 

Cross connectors 

are installed during the frame 

assembly.

38R23S1

37R23S1D

38R23S1

37R23S1D

Bolt head to 

the outside of 

the shelter.

104302 

Rafter Foot

FAG363 

Bolt

FALB04B 

Nut

Step 3

38R23P2

Summary of Contents for Growers Supply GrowSpan Round Pro




















































Reviews:

No comments

Related manuals for Growers Supply GrowSpan Round Pro

Outsunny 845-059V01 Assembly & Instruction Manual preview
845-059V01
Brand: Outsunny Pages: 43
KING CANOPY GH1010 Quick Start Manual preview
GH1010
Brand: KING CANOPY Pages: 7
Halls Greenhouses Qube 66 Assembly Instructions Manual preview
Qube 66
Brand: Halls Greenhouses Pages: 48
AeroGarden AeroGarden 300417AA Replacement Instructions preview
AeroGarden 300417AA
Brand: AeroGarden Pages: 1
FILCLAIR Splendid 3,00x1,50 m Manual preview
Splendid 3,00x1,50 m
Brand: FILCLAIR Pages: 27
Dancover ARROW GH120020 Manual preview
ARROW GH120020
Brand: Dancover Pages: 25
Palram 702284 Manual preview
702284
Brand: Palram Pages: 128

Brands by name

Popular brands

Load more brands