FarmTek 113502 Manual Download Page 4 | Manualshive

Page: 4 / 11

background image

44

Revision date: 01.27.20

2

Assemble Main Frame

ASSEMBLE MAIN FRAME

Assemble frame on a flat, level surface.

1. Use the FAG338B (5/16" x 3") hex head bolts and FAME51B flat washers to complete

the frame assembly.

Tighten all connections until snug.

2. Install one 112770 finishing cap in each horizontal frame tube. Gently tap into tube if

needed.

3. Level the frame as needed. Tighten locknut against the insert plate to secure leveler.

STEP 3

112770

STEP 2

FD15CMGL04900S1

FD15CMGL04900S1

STEP 1

FAME51B

FAG338B

«
...
2
3
4
5
6
...
»

Summary of Contents for 113502












Reviews:

No comments

Related manuals for 113502

Movie FL Black E27 Flaps

Brand: Qazqa Pages: 2

Brand: IDEAL Networks Pages: 8

Brand: IDEAL Networks Pages: 5

Brand: NatureZap Pages: 2

Brand: R&S Pages: 61

Brand: TATU Pages: 30

Brand: Rane Pages: 4

Brand: Sabio Pages: 182

Brand: Daekyung Pages: 15

Brand: Barikell Pages: 32

Brand: Milestone Pages: 64

Brand: BRAND Pages: 21

Firefly 808 Universal

Brand: Phonic Pages: 27

Brand: StarDental Pages: 2

Brand: USC Pages: 29

Brand: Exalto Pages: 28

Brand: POOL LAB Pages: 6

Brand: VividLeds Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands