FarmTek 113502 Manual Download Page 11 | Manualshive

Page: 11 / 11

background image

11

Revision date: 01.27.20

8

Install Bulkhead Screen and Extensions

INSTALL BULKHEAD SCREENS AND EXTENSIONS

Photo above shows the bulkhead screens and extensions installed in

both bulkheads.

Photo above shows the bulkhead screen and extension installed in one

bulkhead. A screen without the extension is installed in the other.

111303

111302

Bulkhead screens and extensions allow you to manage the nutrient solution level in the

propagation tray. Screens can be used with or without the extensions. Depending on the

application, extensions can be used with one screen on the drain tube to increase and maintain

the level of the nutrient solution in the tray. A screen installed on the pump tube deflects water

to ensure an even, steady flow. Install these items as needed to achieve the desired results.

Hand-tighten only during installation.

«
...
9
10
11

Summary of Contents for 113502












Reviews:

No comments

Related manuals for 113502

Brand: DARKSTAR TECHNOLOGIES Pages: 4

Brand: Paitec Pages: 14

Brand: Cadex Pages: 300

Brand: Federal Signal Corporation Pages: 4

Brand: FASTERHOLT Pages: 96

Brand: IDEAL Networks Pages: 10

Brand: Laserworld Pages: 8

Brand: Laserworld Pages: 6

Brand: LaserLiner Pages: 56

Brand: LaserLiner Pages: 54

Brand: Qlight Pages: 4

Brand: Sota Pages: 7

Brand: Biosonic Pages: 2

Brand: Petzl Pages: 7

RGB Studio Beam Driver

Brand: SHOWTEC Pages: 16

Brand: TECshow Pages: 22

Brand: Emos Pages: 8

Brand: Mgl Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands