Farm King 2400 Operator And Parts Manual Download Page 28

Page: 28 / 112

Assembly - Round Bale Carrier 2400

Figure 10

Move the pick-up arm to left front side of the carrier
frame. Align the two mounting brackets (Item 1)

[Figure

10]

with mounts on the left front side of the carrier frame.

Figure 11

Remove the two 1-1/4 x 6-3/4 inch lift arm pivot pins that
are installed in the front and rear pick-up arm mounts on
the carrier frame.

Align the rear mounting bracket (Item 1) of the pick-up
arm with the hole in the rear pick up arm mount (Item 2)

[Figure 11]

on the carrier frame.

NOTE: When installing the 1-1/4 x 6-3/4 inch lift arm

pivot pin, maintain hole alignment of the pin
and collar on the pick-up arm mounting
bracket.

Install one 1-1/4 x 6-3/4 inch lift arm pivot pin (Item 3)

[Figure 11]

through the pick-up arm mounting bracket

and carrier mount (front to rear, with hole in pin towards
the rear).

Figure 12

Install one 3/8” x 2-1/2” bolt (Item 1)

[Figure 12]

through

the collar and pin. Install one 3/8” locknut on the bolt and
tighten.

Figure 13

Remove cable tie (Item 1)

[Figure 13]

from the pick-up

arm lift cylinder.

B-10033

B-10034

B-10064

B-10025

Summary of Contents for 2400

















































































































Search results

Summary of Contents for 2400

Reviews:

Farm King 2400, Operator And Parts Manual, Page: 28 / 112

Search results

Summary of Contents for 2400

Reviews: