Farm King 1370 Assembly Manual Download Page 29

Page: 29 / 94

Assembly - 1370, 1385, 1395, 13114 Backsaver Auger

Figure 86

Align the truss (Item 1) with the tube mount (Item
2) and mount bracket (Item 3)

[Figure 86]

Attach the truss to the tube mount (Item 2) using
one 5/8" X 2" hex bolt, two 5/8" flat washers (both
sides), and one 5/8" lock nut

[Figure 86]

Attach the truss to the mount bracket (Item 3)
using two 5/8" x 1-3/4" flat head socket bolts and
two 5/8" lock nuts

[Figure 86]

Repeat to install the truss on the opposite side.

Do not tighten the bolts at this time.

NOTE:

1395 Model is pictured. The procedure is
the same for all auger models.

Figure 87

Install one truss clamp (Item 1) over the truss.
Attach using two 5/8” x 2” hex bolts, two 5/8" flat
washers, and two 5/8" lock nuts

[Figure 87].

Repeat to install clamp on the opposite side.

Tighten bolts and nuts.

FRONT

Summary of Contents for 1370































































































Search results

Summary of Contents for 1370

Reviews:

Related manuals for 1370

Brands by name

Popular brands

Farm King 1370, Assembly Manual

Search results

Summary of Contents for 1370

Reviews:

Related manuals for 1370

Brands by name

Popular brands