background image

 

<

文档标题

>

 

 

Fanvil Technology Co., Ltd 
HQ Add: Level 3, Block A, Gaoxinqi Building, Anhua Industrial Park, Qianjin 1 Road, 35th District, Bao'An, Shenzhen, 518101 P.R. China 
Tel: +86-755-2640-2199    Fax: +86-755-2640-2618    Email: [email protected]      [email protected]     

Beijing Tel:+86-10-5753-6809

     

Suzhou Tel: +86-512-6592-0605      SEA Tel: +60-3-512-21997 

 

Setting Up 

In order to get the device ready for making and receiving phone calls, the device must be configured 

with  correct  network  configurations  and  at  least  one  of  the  lines  must  be  configured  with  an  IP 

telephony service.   

 

5.1 

Network Configuration 

The  device  relies  on  IP  network  connection  to  provide  service.  Unlike  traditional  phone  system 

based  on  a  circuit  switched  wire  technology,  IP  devices  are  connected  to  each  other  over  the 

network and 

exchange data in packet basis based on the devices’ IP address.   

 

To  enable  the  device,  the  network  parameters  must  be  configured  properly  first.  To  configure 

network parameters, user should open the network configuration screen through soft-menu [Menu] 

-> [Settings] -> [Advanced Settings] -> [Network] -> [Network Settings] from standby screen. 

 

NOTICE!  If  user  saw  a 

 

‘WAN  Disconnected’  icon  flashing  in  the  middle  of  screen,  it 

means the network cable was not correctly connected to the device

’s network port. Please 

check  the  cable  is  connected  correctly  to  the  device  and  to  the  network  switch,  router,  or 

modem.

 

 

There are three common IP configuration modes. 

 

Dynamic  Host  Configuration  Protocol  (DHCP) 

– This is the automatic configuration mode by 

getting  network  configurations  from  a  DHCP  server.  Users  need  not  to  configure  any 

parameters  manually.  All  configuration  parameters  will  be  getting  from  DHCP  server  and 

applied to the device. This is recommended for most users.   

 

Static  IP  Configuration 

–  This  option  allows  user  to  configure  each  IP  parameters  manually, 

including IP Address, Subnet Mask, Default Gateway, and DNS servers. This is usually used in 

an office environment or by power users. 

 

PPPoE 

– This option is often used by users who connect the device to a broadband modem or 

router.  To  establish  a  PPPoE  connection,  user  should  configure  username  and  password 

provided by the service provider. 

 

The device is default configured in DHCP mode. 

Summary of Contents for X5



















































































Reviews: