
MACS II User Manual
101796668
Revision E
22
Ensure these limit switches are adjusted to stop the rotation when the end limit is
attained.
Use the following checklist to verify proper motion and alignment of the various MCS
components. Perform the alignments using the software or by manually actuating
the respective solenoids.
Verify that the cell top and bottom align and mate properly without
interference.
Verify that the drawer moves in and out freely.
With the drawer at out position, verify that the slurry cup can be easily loaded
into the cell.
Verify that the top plate assembly raises and lowers properly.
Verify that the cell can rise and lower smoothly. If necessary, use 0.020-in
and 0.060-in filler gauges to adjust the height. Note that the 0.020-in gauge
should move freely between the cell top and cell bottom when the cell is
raised. A 0.060-in gauge should not move or be hard to put between the two
assemblies.
4.2.5.
Water Test
A heated and pressurized water test can detect leaks and other problems. Perform
the following steps:
1.
Fill the slurry cup with water.
2.
Apply heat and pressure to the water to a maximum of 250
°
F (121.1
°
C) and
20,000 PSI (137.9 MPa; 1,406.5 Kg/cm; 1,379.3 Bar).
3.
Inspect for any leaks or other obvious problems.
4.
Fix minor problems by tightening or reconnecting.
5.
Document any problems found and contact Fann Customer Support.
4.3.
Software Installation
Fann provides the following software to operate and configure the MACS II on a
DVD-ROM included with the system:
MACS II SGS Software Components
Edgeport USB Drivers for Microsoft Windows
Install the software on the dedicated computer associated with the unit. Verify that
this computer meets or exceeds the requirements. Refer to
for computer hardware specifications to run the MACS II SGS
software.
Summary of Contents for MACS II
