background image

32

6.3.7   FOR (force), SPR (spring), DPR (damper)

FOR range: OFF   010 … 120 

FOR default: 100 (%)

SPR range: OFF   010 … 120 

SPR default: 100 (%)

DPR range: OFF   010 … 120 

DPR default: 100 (%)

These force feedback modifiers give you the ability to change the force feed-

back signals of a game (only applicable if game uses these effects). In theory 

there are three types of signals which a game can send: Force (pushes the 

wheel in a specific direction), spring (pulls the wheel towards the dynamic cen

-

tre) and damper (creates friction). Not every game uses all types of effects and 

some games even use only one type to create all different feelings. Using your 

Tuning Menu in the CSL Elite Wheel Base+ you can increase or reduce these 

different effects individually. To change the active value, move the directional 

stick of the Fanatec

®

 steering wheel up or down.

Note: 

If SPR is set to low values or ‘OFF’ the CSL Elite Wheel Base+ will not 

be able to move the attached steering wheel to the correct centre position after 

calibration run.

 

IMPORTANT:

 Only set these values higher than 100% if the force feed

-

back effects are clearly not strong enough and weaker in comparison to 

other games. When the game sends full effects and the wheel is set to 

100% then the device will work on its power limit. Pushing up one value 

to a very high number or even raising multiple values will result in higher 

load on the motor and increased heat generation.

For further information check the FAQ section on our website

www.fanatec.com/support

.

Summary of Contents for CSL Elite Wheel Base +



















































Reviews: