background image

F-40 Laminator Operator Manual

Operation

© GBC Pro-Tech 1998 February

3-7

6HWXS DQG 3URFHGXUH 3DVV 

1.

Adjust the machine settings as shown in process 
chart 3-4b.

2.

Trim the print to size and trim the board to the size 
of the print.

3.

Insert the board into the nip area and lower the 
main roll until it contacts. Turn the crank another 1/
4 of a turn and remove the board using the foot-
switch.

4.

Clean the board with a tack cloth or cleaning roller.

5.

Place the image face down on a flat surface and 
peel back the release liner on the leading edge 
(about two inches).

6.

Lay the image on the board and align it carefully. 
When aligned, tack the exposed adhesive strip's 
center to the leading edge to the board. Work 
towards the edges from the center, being careful 
not to wrinkle the image.

7.

Position the piece so that the end with the liner 
peeled back is facing the nip. Insert the first one 
inch of the board into the nip. Very carefully, wrap 
the print back and over the top laminating roll, 
maintaining good print tension throughout the 
mounting process. Be sure that there are no wrin-
kles in the nip area. Carefully peel off the liner as 
the board progresses through the laminator.

8.

Trim the board and image to the finished size.

7ZR3DVV 0RXQW DQG /DRW

2YHUODPLQDWH

This process is very similar to the Two Pass Mount and 
Laminate using cold overlaminate.

6HWXS DQG 3URFHGXUH 3DVV 

1.

Adjust the machine settings as shown in process 
chart 3-5a and remove the infeed table.

2.

Web up the hot overlaminate by wrapping it around 
the upper film idler and draping it over the upper 
main roll. Drape the film only about halfway down 
the upper main roll. 

3.

Pull the mount adhesive straight up from the lower 
unwind position, being careful not to stick the film 
to the machine. Tack it to the hot overlaminate.

4.

Insert a starter board into the nip and lower the 
upper main roll onto it.

5.

Press the footswitch. Once the leader board is 
through the nip, lower the upper main roll and then 
rotate the crank 1/2 a turn more.

6.

Reinstall the infeed table.

7.

Encapsulate the images.

6HWXS DQG 3URFHGXUH 3DVV 

1.

Adjust the machine settings as shown in process 
chart 3-5b.

2.

Trim the print to size and trim the board to the size 
of the print.

3.

Insert the board into the nip area and lower the 
main roll until it contacts. Turn the crank another 1/
4 of a turn and remove the board using the foot-
switch.

4.

Clean the board with a tack cloth or cleaning roller.

5.

Place the image face down on a flat surface and 
peel back the release liner on the leading edge 
(about two inches).

6.

Lay the image on the board and align it carefully. 
When aligned, tack the exposed adhesive strip's 
center to the leading edge to the board. Work 
towards the edges from the center, being careful 
not to wrinkle the image.

7.

Insert the already mounted portion of the piece into 
the pull roll nip. Lower the upper pull roll onto the 
board and image. Very carefully, wrap the print 
back and over the upper pull roll, maintaining good 
print tension throughout the mounting process. Be 
sure that there are no wrinkles in the nip area. 
Carefully peel off the liner as the board progresses 
through the laminator. Be careful not to hit the 
small lip on the fan bridge to avoid damaging the 
leading edge of the mounted image.

8.

Trim the board and image to the finished size.

Summary of Contents for F-40

















































Reviews: