background image

Installation

F-40 Laminator Operator Manual

2-8

© GBC Pro-Tech 1998 February

6WDUWXS

The first time the laminator is started and every time it 
is serviced you should use the following checklist to 
confirm that the unit is operating properly and that all 
safety mechanisms are functioning.

Startup Checklist

Start the laminator and go through the following check-
list.

Are the emergency stop buttons working?
Push down on one of the emergency stop buttons. 
The laminator should stop. Pull up on the button. 
The laminator should resume operation. Always 
check both buttons.

 WARNING

Is the photoelectric eye system working?
With the laminator running, place an object 
approximately the size of your hand just in front of 
the nip to confirm that the photoelectric eye system 
is functioning. The 

roll

s should stop. Move the 

object away from the nip. The laminator should 
resume operation.

 WARNING

Is the motor functioning?
Test the motor at various speeds ranging from 
0-18. At 0 the 

roll

s should stop turning.

Run the motor in both forward and reverse.

Are the heaters working?
Verify that the top heater controller heats the top 
roll and the bottom heater controller heats the bot-
tom roll.

Is the footswitch operating?
Test the footswitch for both forward and reverse 

operation. Verify that the footswitch overrides the 
photoelectric eye by pressing the footswitch and 
pushing an object as large as your hand into the nip 
area.

Once you have completed the startup checklist you can 
safely run a test sample.

Never operate the laminator unless both of the 

emergency stop buttons are functioning  

properly. You can be crushed or burned.

Never operate the laminator unless the 

photoelectric eye system is functioning properly. 

You  can be crushed or burned.

Summary of Contents for F-40

















































Reviews: