background image

F-40 Laminator Operator Manual

Warranty

© GBC Pro-Tech 1998 February

5-1

6HFWLRQ   :DUUDQW\

/LPLWHG :DUUDQW\

GBC Pro-Tech Engineering Company, Inc. warrants 
the equipment sold is free from defects in material and 
workmanship for a period of ninety days (90) from the 
date of delivery
 to the customer. This warranty is the 
only warranty made by GBC Pro-Tech and cannot be 
modified or amended.

GBC Pro-Tech’s sole and exclusive liability and the 
customer’s sole and exclusive remedy under this 
warranty shall be, at GBC Pro-Tech’s option, to 
repair or replace any such defective part or prod-
uct. These remedies are only available if GBC Pro-
Tech’s examination of the product discloses to GBC 
Pro-Tech’s satisfaction that such defects actually 
exist and were not caused by misuse, neglect, 
attempt to repair, unauthorized alteration or modi-
fication, incorrect line voltage, contaminated air 
supply, or by fire, accident, flood, or other hazard.

This warranty specifically does not cover damage to 
the laminating rollers caused by knives, razor blades, 
other sharp objects, failure caused by adhesives or 
improper use of the machine. Warranty repair or 
replacement does not extend the warranty beyond the 
initial ninety day period from the date of delivery.

  CAUTION

THE WARRANTY MADE HEREIN IS IN LIEU OF 
ALL OTHER WARRANTIES, EXPRESS OR 
IMPLIED, INCLUDING ANY WARRANTY OR 
MERCHANTABILITY OR FITNESS FOR A PAR-
TICULAR PURPOSE. GBC PRO-TECH WILL NOT 
BE LIABLE FOR PROPERTY DAMAGE OR PER-
SONAL INJURY (UNLESS PRIMARILY CAUSED 
BY ITS NEGLIGENCE), LOSS OF PROFIT OR 
OTHER INCIDENTAL OR CONSEQUENTIAL 
DAMAGES ARISING OUT OF THE USE OR 
INABILITY TO USE THE EQUIPMENT.

([FOXVLRQV WR WKH :DUUDQW\

This warranty specifically does not cover:

1.

Damage to the laminating rolls caused by knives, 
razor blades, other sharp objects, or failure caused 
by adhesives.

2.

Damage to the machine caused by lifting, tilting, 
and/or any attempt to position the machine other 
than rolling on the installed casters on even sur-
faces.

3.

Improper use of the machine.

Unauthorized customer alterations will void this 

warranty.

Summary of Contents for F-40

















































Reviews: