English
18
Please see the typeplate or the section ”Specifications” for the
connection values.
Operation
Danger of life!
Vehicle tyres/tyre valves may be damaged and burst by the high-
pressure jet. A first sign is the discoloration of the tyre. Damaged
vehicle tyres/tyre valves are hazardous. Always perform the cle-
aning with a distance of at least 30 cm. Never touch the mains
plug with wet hands. Check the power cord and the mains plug
for damages prior to each use of the appliance. If the power cord
is damaged, please arrange immediately for the exchange by an
authorised customer service or a skilled electrician.
Check the high-pressure hose for damages prior to each use of
the appliance. If the high-pressure hose is damaged, replace it
immediately.
Danger of injury!
Due to the water jet emerging from the high-pressure nozzle, a
recoil force acts on the trigger gun. Always ensure a stable stan-
ding position and hold the trigger gun and the spray jet firmly.
If necessary, wear protective clothes for the protection from re-
turn spray.
Water supply:
Note:
Dirt in the water supply can damage the unit. We recom-
mend the use of a water filter (3/4") fitting, to avoid this
If the high-pressure cleaner is operated with a closed water sup-
ply line, the cylinder head unit will be damaged.
Never operate
the high-pressure cleaner with a closed water tap.
• Connect a supply hose (not included in the delivery) to the water
connection of the appliance and to the water supply.
• Open the water supply.
Preparing the Appliance
• Insert the spray lance, and twist into the locked position
• Insert the mains plug.
• Set the main switch to ”I”.
Turning On the Appliance
• Press the safety button on the trigger gun, and pull the lever.
Turning Off the Appliance
• Release the lever.
Press the safety button to prevent the appliance from being
inadvertently turned on during breaks or if you leave the ap-
pliance.
• Main switch to ”0”.
• Close the water supply tap.
Adding the cleaning agent
• Remove spray lance
No detergent in high-pressure mode
• Draw the cleaning agent suction hose out of the housing to the
required length (max. 35 cm).
• Hang the cleaning agent suction hose in the cleaning agent
container.
If detergent has been added:
• Put the detergent suction hose into a container with clear water,
turn on the appliance for approximately 1 minute, and perform
a clear rinsing.
Recommended Cleaning Method
1.Spray a small dose of the detergent on the dry surface, and
allow it to react (make sure the detergent does not dry up).
2.Wash off the loosened dirt using the high-pressure jet.
Terminating the Operation
• Release the lever.
Press the safety button to prevent the appliance from being
inadvertently turned on during breaks or if you leave the ap-
pliance.
• Main switch to ”0”.
• Disconnect the mains plug.
• Close the water supply tap.
• Press the lever (depressurize)
• Disconnect the appliance from the water connection.
Storing the Appliance
Caution
! Frost may destroy the appliance if it has not been
emptied completely. Store the appliance in a frost-free room during
the winter.
• Remove spray lance from trigger gun by pushing it in and twi-
sting
• Wind up the power cord and, for example, hang it around the
handle.
Maintenance and Care
Before any care and maintenance work on the machine
draw out the mains plug.
Cleaning
Before long periods of storage, e.g. in winter:
• Remove the sieve in the water connection using flat pliers, and
clean it under running water.
Maintenance
The appliance is maintenance-free.
Troubleshooting
Failures often have simple causes that you can resolve yourself
using the following overview. In case of difficulty, or to obtain a
remedy to an issue not discussed here, please contact your re-
tailer.
Danger of electric shock!
Repair work on the appliance may only be performed by the
authorised customer service.
Before any care and maintenance work on the machine draw out
the mains plug.
Appliance does not work
- Please check whether the voltage specified on the typeplate
corresponds to that of the power source.
- Check the power cord for damages.
Appliance does not achieve the operational pres-
sure
- Deaerate the appliance: allow the pump to operate without the
high-pressure hose until bubble-free water emerges from the
high-pressure outlet. Then reconnect the high-pressure hose.
- Clean the sieve in the water connection (it can be easily remo-
ved using flat pliers).
- Check the inlet water flow rate.
- Check all supply lines to the pump for leaks or clogging-up.
Strong pressure variations
- Clean the high-pressure nozzle. Remove dirt from the nozzle
boring using a needle, and then rinse the nozzle with water.
