background image

VIGILO

VIGILO

10

Post cover

Rubber buffer

Cover plate

Retractable
post

230 V

230 V

=

=

NO

22 23

GREASE

IMPORTANT:
WE RECOMMEND
GREASING ALL CLAMPING
SCREWS

1

2

3

4

5

6

7

8

9

10

11

12

1

2

3

4

5

6

7

8

9

10

11

12

1

4

2

3

5

English

fully retractable oil-hydraulic bollard

VERSION OF CORAL WITH SOLENOID VALVE

In the version of 

VIGILO with solenoid valve

 no manual overriding action is needed, and in case of power failure the post descends 

automatically flush with pavement level. To enable the solenoid valve to operate properly, the electric wires labelled 
“ELETTROVALVOLA - Solenoid valve” from the post assembly are to be connected, through the 

voltage stabilizer

, to terminals 22 

and 23 in the Elpro S40 control box.

Pic. 12

VIGILO with solenoid valve

VIGILO with solenoid valve

VIGILO with solenoid valve

SOLENOID VALVE

STABILIZER

GROUND-LEVEL CLOSURE - COVER PLATE

• Use the four screws to close the cover plate.
• Lift the retractable post for facilitate closure of the post cover 
with the buffer, give the command (by encoding a transmitter 
with the radio receiver or a key switch) to lift the retractable 
post.

Pic. 13

MANUAL RELEASE OPERATIONS

In the case of a blackout, the post can be lowered manually following the instructions show in pic. 14.

Insert the release key

in the release key recess

Release the hydraulic circuit
by turning the release key
one turn anti-clockwise

Press to lower the post manually

Pic. 14

Block the hydraulic circuit
by turning the release key
clockwise (tighten until
securely locked)

Summary of Contents for VIGILO 2250

















Reviews: