background image

8

INSTRUCTION MANUAL DAAB VEHICLE DETECTOR DB402

Revision 7

Loop safety functions

You can use the following channels to select and configure these safety functions.
d140, Safety when closing

Used to configure the safety setting in the closing movement. The value 0 means the function is disabled – note that the 

door will close even if there is a vehicle on the loop. Set the value to 1 to reverse the door when something is detected by 

the vehicle loop, set the value to 2 to send a stop signal with automatic closing, or set the value to 3 to send a stop signal 

without automatic closing. The automatic closing timer starts when the vehicle exits the loop.
d141, Safety during run-on time

This channel activates safety during the run-on time The safety function is the same as specified in d140. Set the value of 

this channel to 0 to disable safety during the run-on time, or 1 to activate it.
d142, Safety function when opening

This channel sets the safety function in the opening movement – 0 means the function is disabled. The value 1 means 

reverse, 2 means stop with automatic restart when the loop is clear, and 3 means stop and wait for a new control signal, 4 

provides a safety function only in the closed position.

Summary of Contents for DAAB DB402















Reviews: