background image

INSTRUCTION MANUAL DAAB VEHICLE DETECTOR DB402

Revision 7 

11

Vehicle loop 2

Note that the display of the d-channels is determined by the setting in C702 for EP105

No. 

Name

Range

Factory Setting

d200

Vehicle loop 2

0 - 1

0

0

Disabled

1

Enabled

d201

Loop reading x1

000 - 999

d202

Loop reading x1000

00 - 99

d203

Activation from passing vehicle

000 - 999

d210

Detection limit for a vehicle in the loop

05 - 99

15

d211

Difference between on and off in the loop

00 - 50

03

d220

Loop presence reset

000 and 005-240 

minutes

120

d221

Fast loop presence reset

00-99 seconds

00

d231

Compensation for activation from door half motor 1 on the 

loop in the closed position

00 - 50

03

d232

Compensation for activation from door half motor 2 on the 

loop in the closed position

00 - 50

03

d240

Safety function in closing movement

0 - 4

1

0

Disabled

1

Reverse

2

Stop with automatic restart of automatic closing

3

Stop without automatic restart of automatic closing, wait for new control signal

4

Safety only in open position. Used when the gate passes over the loop in the closing movement.

d241

Safety during run-on time or disengagement angle in closing 

movement.

0 - 1

1

0

Disabled

1

Activated according to d240

d242

Safety function in opening movement

0 - 4

0

0

Disabled

1

Reverse to fully closed

2

Stop with automatic restart of automatic closing

3

Stop without automatic restart of automatic closing, wait for new control signal

4

Safety only in closed position. Used when the gate passes over the loop in the opening movement.

d251

Loop closing

0 - 1

0

0

Disabled

1

Enabled

d254

Type of closing with loop

1 - 2

2

1

Close immediately when loop is clear

2

Open fully first, then close

Summary of Contents for DAAB DB402















Reviews: