AIRSLIDE
37
532225 - Rev.A
28
1
2
0
1 2 3 4 5 6 7
Tr
ansla
tion of the original instruc
tions
ENGLISH
7.6 J7 - MOTOR INPUTS
It is possible to connect 2 motors, M1 and M2, to connector J7.
The second motor M2 is connected for electric fan modules
with more than three fans.
7.7 J5 - MAINS POWER SUPPLY
The E1AS is powered on connector J5 with
230Vac 50/60Hz mains power. The board automatically recognises
the mains voltage frequency.
When the board is switched on, LED DL 3 flashes to indicate
that it is operating correctly.
During movement of motor 1 or motor 2, LED DL3
will remain steadily lit.
When movement of motor 1 or motor 2 finishes, LED DL3
will begin to flash again.
7.8 BUTTONS SW5 AND SW6
There are 2 buttons on board E1AS :
1.
SW5 Motor test button – Operates the motor at maximum speed
when pressed. It has priority over all other inputs.
2.
SW6 Board reset button – Pressing this resets the board
7.9 DIP SWITCHES SW1 AND SW2
There are 2 DIP switches on board E1AS :
1.
SW1 2-way DIP switch for adjustment of speed 1
•
DIP switch OFF - OFF (High speed)
•
DIP switch ON - OFF (Medium-High speed)
•
DIP switch OFF - ON (Medium-Low speed)
•
DIP switch ON - ON (Low speed)
2. SW2 2-way DIP switch for adjustment of speed 2
•
DIP switch OFF - OFF (High speed)
•
DIP switch ON - OFF (Medium-High speed)
•
DIP switch OFF - ON (Medium-Low speed)
•
DIP switch ON - ON (Low speed)
7.10 DIP SWITCHES SW3 AND SW4
It is possible to assign an ID address on board E1AS
communication using DIP switch SW4 on board E1AS.
DIP switch SW3 is not used.
The ID assignment table is given below:
E1AS
SW4
E1SL ID
ID
1234
(SDK EVO)
9
1001
1
10
1010
2
11
1011
3
12
1100
4
13
1101
5
14
1110
6
15
1111
7
7.11 J8 USB INPUT
USB port for E1AS update.
Insert the USB device on J8.
Press button SW6 (Reset) for USB recognition.
LED DL10 will light up and DL3 will switch off.
Press and hold button SW5 (motor test) for 3 seconds and LED DL10
will flash during the update phase.
When the update is complete, LED DL10 will light up steadily and DL3
will turn on.
Remove the USB device
The name of the file to be loaded on the USB device is:
•
E1AS.hex E1AS board firmware
The update files may be downloaded from the website:
www.faacgroup.com
The USB device must be formatted with FAT or FAT 32 file system. The
NTFS format is not recognised by the control board.
The necessary files must be directly available on the USB storage
medium with the precise names defined; they must not be zipped
or inside folders.
Use a USB with maximum 500mA absorption.
7.12 E1AS BOARD OPERATION
Board E1AS manages the activation of the electric fan unit via com-
mands received from other boards or from the operator.
The commands can be received via Inputs (J1) or via
CAN BUS (J2)
27
.
It is also possible to use a single system for the commands.
If both are used, the commands on J1 have priority.
The fan turns on in the conditions specified
in table
29
.
The fan will be switched off under all other conditions.
The following is a table with the various configurations
connected to the inputs for button P1,P0,P2 and the inputs for
management
of external commands I1, I2.
The commands from the CanBus are also taken into consideration.
The speed column allows speed V1 or V2 to be determined.