40
ENGLISH
ENGLISH
SD-KEEPER off
•no mains power supplied and the 940SDM control board is battery-powered in NIGHT operating function,
and in energy saving statues.
•connection to the 940SDM control board is interrupted: check the connection cables and wiring between
SD-Keeper and the 940SDM control board
•940SDM control board not operating correctly; replace the 940SDM control board
A
TROUBLESHOOTING
TROUBLESHOOTING
TROUBLESHOOTING
TROUBLESHOOTING
TROUBLESHOOTING
The following will help you identify and solve some particular states.
LEDs
MAIN, V
ACC
, VMOT and +24V
OFF
•check if the F2 5x20 T1A fuse on the 940SDM control board is interrupted
•is the 5x20 T1A fuse inside the power supply unit interrupted?
•Is connector J2 fitted correctly on the 940SDM control board?
•check connection to the power supply unit
•940SDM control board not operating correctly; replace the 940SDM control board
B
MAIN LED OFF;
V
ACC
, VMOT and +24V LEDs
all ON
•mains power not supplied and the 940SDM control board is battery-powered
•if mains power is being supplied, see point B
C
MAIN and V
ACC
LEDs OFF;
VMOT and +24V LEDs ON
•no mains power supplied, the 940SDM control board is battery-powered and in energy saving statues.
•if mains power is being supplied, see point B
D
VMOT LED OFF;
MAIN, V
ACC
and +24V LEDs
ON
•is the F1 5x20 T6.3A fuse on the 940SDM control board interrupted?
•Is connector J3 fitted correctly on the 940SDM control board?
•check if the power supply unit and the control board are efficiently connected
•940SDM control board not operating correctly; replace the 940SDM control board
E
VMOT and V
ACC
LEDs OFF;
MAIN and +24V LEDs ON
•this state occurs when the control board software is being updated
•there may be condensation on the board; cut power and dry the dampness.
•940SDM control board not operating correctly; replace the 940SDM control board
F
ERROR LED flashing slowly
•alarm in progress: connect the SD-Keeper to find the alarm and take the appropriate action (see the
diagnostics guide)
G
door locked and ERROR LED
ON
•SETUP must be executed
•alarm in progress: connect the SD-Keeper to find the alarm and take the appropriate action (see the
diagnostics guide)
•check motor connection
•check motor encoder connection
•check the condition of the encoder connection flat cable
H
door NOT executing SETUP
and ERROR LED flashing
slowly
•SETUP execution impeded (see 940SDM control board instructions)
I
door NOT CLOSING and
ERROR LED off
•photocell/s engaged
•make sure that the selected operating function is not DOOR OPEN (if no SD-Keeper is installed, make sure
that input 8 of the J6 terminal board is not jumper connected to the negative)
•make sure that the selected operating function is not MANUAL
•check motor connection
•check if power is being supplied to the motor (VMOT LED ON)
L
door NOT OPENING and
ERROR LED off
•make sure that the selected operating function is not MANUAL
•make sure that the selected operating function is not NIGHT (if no SD-Keeper is installed, make sure that
input 7 of the J6 terminal board is not jumper connected to the negative)
•check motor connection
•make sure that the lock is not locked
•check if power is being supplied to the motor (VMOT LED ON)
M
door CLOSES instead of
OPENING and vice versa
•reverse the position of dip-switch 1 on the 940SDM control board and execute a SETUP
N
door moving for short
distances only
•check if encoder connector J4 is correctly inserted
•check condition of the encoder
•check the condition of the encoder connection flat cable
O
door movements very slow
•using the SD-Display, check if the selected speed levels are as required
•using the SD-Display, check if the selected deceleration distances are as required
P
ERROR LED flashing rapidly
•door executing a SETUP; wait for the procedure to end
•door executing a RESET; wait for the procedure to end
•with the KIT ELASTIC installed, the door is resetting the elastic; wait for the procedure to end
Q
STATE
SUGGESTION
