FAAC 940SMT, Manual

Page: 34 / 42

33
ENGLISH ENGLISH
55555 DIAGNOSTICS DIAGNOSTICS
DIAGNOSTICS DIAGNOSTICS DIAGNOSTICS
5.1 940SDM 5.1 940SDM
5.1 940SDM 5.1 940SDM 5.1 940SDM
The door's hardware model and the software of the 940SDM
control board to which SD-Keeper is connected are shown.
5.2 NR. CYCLE 5.2 NR. CYCLE 5.2 NR. CYCLE 5.2 NR. CYCLE 5.2 NR. CYCLE
The count (non resettable )of the cycles effected by the door
is shown.
5.3 ALARM N. 5.3 ALARM N. 5.3 ALARM N. 5.3 ALARM N. 5.3 ALARM N.
The number and description of the current alarm are shown.
No. DESCRIPTION MEANING
ENERGY SAV. Operating on low battery consumption
1 SPEED CHANGES Speed changed, new setup required
2 BAT.OPERATION. Door operating on battery
3 FORCED OPEN
Door forced opening in progress
4 FLAT BATTERY Battery discharged: emergency movement not
guaranteed
6 EMERG 2 ON Emergency 2 input active
7 EMERG 1 ON Emergency 1 input active
8 OBST. IN OPEN. Opening obstacle detected 3 successive times;
Reset necessary to restore operation
9 OBST. IN CLOS. Closing obstacle detected 3 consecutive times;
Reset necessary to restore operation
10
콯
Lock locked in closed position
11
콯
Lock locked in open position (with surveillance kit only)
12
콯
Incorrect power supply to motor (VMOT absent)
13
콯
Photocell 2 faulty (PSW2 input)
14
콯
Photocell 1 faulty (PSW1 input)
15
콯
Setup not possible
18
콯
Initialisation process not possible on motor : leaf stroke
too long
20
콯
Initialisation process not possible on motor: insufficient
leaf stroke
22
콯
Initialisation process not possible on motor: too much
friction
24
콯
Motor malfunctions
25
콯
940SDM control board faulty
RESET RESET
RESET RESET
RESET
Executes reset procedure.
66666 ADVANCED MENU ADVANCED MENU
ADVANCED MENU ADVANCED MENU
ADVANCED MENU
P PP
PPAS
AS
AS AS ASSWORD
SWORD
SWORD SWORD SWORD
To access the advanced menu, insert the 4-digit password
(default 0000).
1 OPERA 1 OPERA 1 OPERA 1 OPERA 1 OPERATION P TION P TION P TION P TION PARAMETERS ARAMETERS ARAMETERS ARAMETERS ARAMETERS
1.1 CL 1.1 CL
1.1 CL 1.1 CL 1.1 CLOSING SPEED
OSING SPEED
OSING SPEED OSING SPEED OSING SPEED
Sets door speed for closing.
When speed is changed with respect to the set value, an
alarm is signalled on the control board (“Error” LED flashing
slowly) and on the SD-Keeper (ALARM 1: speed change) - a
new Setup is recommended.
Standard value: level 3.
Adjusting range: from 0 to 10
1.2 OPENING SPEED 1.2 OPENING SPEED
1.2 OPENING SPEED 1.2 OPENING SPEED 1.2 OPENING SPEED
Sets door speed for opening.
Standard value: level 10 (maximum speed)
Adjusting range: from 0 to 10
1.3 DECEL. WIDTH 1.3 DECEL. WIDTH
1.3 DECEL. WIDTH 1.3 DECEL. WIDTH 1.3 DECEL. WIDTH
Opening Opening Opening Opening Opening
Sets anticipated time value on the standard deceleration
point at the opening stop position.
Standard value: 0 cm
Adjusting range: from 0 to 120 cm
Closing Closing Closing Closing Closing
Sets anticipated time value on the standard deceleration
point at the closing stop position.
Standard value: 0 cm
Adjusting range: from 0 to 120 cm
1.4 DECEL. SPEED. 1.4 DECEL. SPEED. 1.4 DECEL. SPEED. 1.4 DECEL. SPEED. 1.4 DECEL. SPEED.
Speed: Speed:
Speed: Speed:
Speed:
Sets speed level during deceleration.
Standard value: low
Adjusting range: high/medium/low
2 IN/OUT SETUP 2 IN/OUT SETUP
2 IN/OUT SETUP 2 IN/OUT SETUP 2 IN/OUT SETUP
2.1 Emerg 1 2.1 Emerg 1
2.1 Emerg 1 2.1 Emerg 1
2.1 Emerg 1
2.2 Emerg 2
2.2 Emerg 2
2.2 Emerg 2 2.2 Emerg 2 2.2 Emerg 2
Sets the effect of the emergency commands (Emerg1 and
Emerg2 inputs on 940SDM control board).
Standard setting EMERG 1:
Stop/No memory/NO
Standard setting EMERG 2:
Open/Speed: Standard/No memory/ NO
Open Open
Open Open Open
Activating this command opens the door.
Close Close Close Close Close
Activating this command closes the door.
Stop Stop
Stop Stop
Stop
Activating this command stops the door.
Speed: Standard Speed: Standard Speed: Standard Speed: Standard Speed: Standard
The door opens or closes (according to setting) at normal speed.
Speed: No Standard Speed: No Standard Speed: No Standard Speed: No Standard Speed: No Standard
The door opens or closes (according to setting) at slow speed.
No memory No memory
No memory No memory No memory
In order to keep the emergency active, the command must
be maintained active (on release, the door returns to normal
operation).
With memory With memory With memory With memory With memory
A pulse keeps the emergency operational;
To restore operation, resetting is necessary either from the control
board or from SD-Keeper.
N o N o N o N o N o
Normally open input.
N c N c N c N c N c
Normally closed input.
2.3 Photocells 2.3 Photocells 2.3 Photocells 2.3 Photocells 2.3 Photocells
Quantity Quantity
Quantity Quantity Quantity
Number of connected photocells.
Standard no.: 2
Settable no.: 0, 1, 2
When no photocells are configured and the selected status is
NC (see below), there is no need to jumper connect unused
inputs.
When configuring 1 photocell, you can connect to the PSW1
input of the 940SDM control board.
Failsafe Off Failsafe Off Failsafe Off Failsafe Off Failsafe Off
Failsafe test on photocells not executed.
Failsafe On Failsafe On
Failsafe On Failsafe On Failsafe On
Failsafe test on photocells executed before each movement.
N c N c N c N c N c
Normally closed input.
N o N o
N o N o
N o
Normally open input.
2.4 SENSORS 2.4 SENSORS 2.4 SENSORS 2.4 SENSORS 2.4 SENSORS
Sets the status of “external radar” and “internal radar”
commands (E-Det and I-Det inputs on 940SDM control board).
N o N o N o N o N o
Normally open input.
N c N c
N c N c
N c
Normally closed input.
2.5 KEY 2.5 KEY 2.5 KEY 2.5 KEY 2.5 KEY
Sets the status of the “key” command (Key input on the 940SDM
control board).
N o N o N o N o N o
Normally open input.
N c N c N c N c N c
Normally closed input.