background image

T

HE

 400 O

PERATOR

 

G

ENERAL

 C

HARACTERISTICS

 

 

The FAAC 400 Operator is an automatic gate operator 

for a swinging gate leaf. It can accommodate a gate leaf 

of  up  to  2000  lb  (900  kg)  and  up  to  20  ft  (6  m)  in 

length. 

 

 The self-contained 400 Operator is an electro-hydraulic 

unit  consisting  of  an  electric  motor,  a  pump,  a  valve 

assembly, and a hydraulic cylinder, all housed in an 

anodized aluminum oil reservoir. 

 

 The 400 Operator can be used to swing the gate leaf 

inward or outward. Most versions provide hydraulic 

locking in at least one position, either opened or closed, 

depending on how it was ordered. 

 

 The hydraulic lock is a service device rather than a 

security device. Additional, external locks are 

recommended under the following conditions: 

 

  You are installing the Model 400 SB 

  The length of the gate leaf is 12 ft or more 

  The installation requires tight security 

  The site is subject to vandalism 

  The site is subject to strong or very gusty wind 

  You are installing a solid face gate 

 

For gates with two leaves, two operators are installed, 

one on each leaf, and both are wired to one control 

panel. In such two-operator gate installations, one leaf 

can be programmed to open/ close slightly later than 

the other leaf to accommodate overlapping gate 

designs. 

 For its protection, the single-phase, bidirectional motor 

shuts off automatically if its operating temperature 

reaches 212 deg F (100 deg C). Also for the protection 

and proper operation of the 400 Operator, each gate 

leaf on which it is installed must have a fixed positive 

stop in both the opened and closed positions. 

 

 The 400 Operator also includes a key-operated Manual 

Release mechanism and two bypass valves that 

pre

­

cisely control the force applied to the gate leaf 

through the 400 Operator. 

 

 The Manual Release mechanism is a key-operated 

device that disengages (or engages) the hydraulic 

system of the 400 Operator. When the hydraulic system 

is disengaged, you can open and close the gate leaf by 

hand. Such manual operation of the gate is necessary 

during installation and useful during power failures. The 

two bypass valves are located beneath the locking cap. 

You need to adjust the bypass valves to meet the safety 

standards of FAAC International, Inc. The standards 

state that the gate leaf should stop if it encounters a 

force of more than 33 lb (15 kg). 

 

 Additional reversing devices (such as inductive loops 

and photocells) should be installed to provide more 

complete protection for people and property. 

 

 The electronic control panel is a microprocessor-based 

controller that accepts a wide range of product 

accessories and reversing devices, thus allowing for 

flexible gate system design. 

Page 6 

November, 2003 

400 Operator And  

455 D Control Panel Installation Manual  

P

REPARING

 

THE

 G

ATE

 

 

Before installing the 400 Operator, you need to prepare 

the gate itself for the operator. Be sure to do the 

following things: 

 

1.  Make sure that the gate is plumb.  

2.  Make sure that the gate moves smoothly on its 

hinges without excessive friction by swinging 

it open and closed by hand. Lubricate all the 

gates’ moving parts. 

3.  Provide positive stops for the gate leaves in 

the fully open and fully closed positions (see 

Figure 2). 

I

NSTALLATION

 I

NSTRUCTIONS

 

Installing the 400 Operator involves preparing the gate, 

installing the operator(s), installing the control panel, 

and fine-tuning the pressure adjustments on the 

operator(s). 

 

Note: The following installation instructions 

assume you are fully capable of installing an 

operator. This manual does not instruct you in 

designing a gate, installing a gate, or basic 

electrical wiring. The installation tasks discussed in 

this manual are tasks particular to the 400 

Operator. 

 

Summary of Contents for 455 D





























Reviews: