F.u.n.k.e. TRT800H-OLED Operation And Installation Download

Page: 26 / 50

TRT800H / P/N 800ATC-H-(2xx)-(2xx)

Operation and Installation

Document-No: 03.2124.010.71e / Revision: 2.10

3.8 Antenna

3.8.1 Antenna Selection



Recommended antennas: see section 3.11 Accessories



Choose an antenna type compatible with the vehicle and the

mounting location.



Specified features depend on proper installation of the antenna.



The radiation pattern needs to be verified considering aircraft type

and mounting location.



The electrical interference between the antenna and any other

equipment must be taken into account in such a way that no
reduction of the performance of any other system will occur.



Install only certified antennas!

3.8.2 Installation Recommendation



Take note of the antenna manufacturer’s instructions.



The usually deployed Dipole- or Blade antennas necessarily

require a high frequency capable solid metal ground plane at the
antenna base.



For installation in composite aircrafts, ground planes are to be

added. The ground plane should be as large as possible but in any
case not smaller than 10 cm x 10 cm. If in doubt, please contact
the aircraft manufacturer.



Keep away three feet from any other antenna.



Pursue mounting in vertical position under the belly in flight

direction.

3.8.3 Antenna Wiring



Suitable antenna cables: see section 3.11 Accessories



Keep wiring as short as possible.



The smallest cable bend radius is 10cm. Avoid sharp bends.



Keep away from an ADF antenna cable at least 12 inches.



Electrical connections to the antenna shall be protected against

moisture to avoid loss of efficiency.

Summary of Contents for TRT800H-OLED



















































Search results

Summary of Contents for TRT800H-OLED

Reviews:

Related manuals for TRT800H-OLED

Brands by name

Popular brands

F.u.n.k.e. TRT800H-OLED, Operation And Installation

Search results

Summary of Contents for TRT800H-OLED

Reviews:

Related manuals for TRT800H-OLED

Brands by name

Popular brands