F.u.n.k.e. TRT800H-OLED Operation And Installation Download Page 45

Page: 45 / 50

TRT800H / P/N 800ATC-H-(2xx)-(2xx)

Operation and Installation

Document-No: 03.2124.010.71e / Revision: 2.10

Fuse

External 2A-slow-blow fuse

Mounting

Panel cut-out d=57,5 mm

Weight

0,6 kg (1.32 lbs.)

Receiver Characteristics:

Sensitivity

RF input power level resulting in a 90 %
reply rate:

A. MTL for ATCRBS and ATCRBS/Mode S

All-Call interrogations: -74 dBm ±3 dB.

B. MTL for Mode S interrogations:

-74 dBm ± 3 dB.

Reply transmission
frequency

1090 ± 1 MHz

RF Peak Power Output



21 dBW (126 W) at antenna base

(with maximum cable attenuation of 1,5 dB)

Squitter (ADS-B)

transmitted at random intervals uniformly
distributed over the range from 0.8 to 1.2
seconds, full self-verification of data and
occurrence

Mode S Elementary Surveillance

ICAO 24-bit Aircraft
Address (Hex-Code)

aircraft address as assigned by national
aviation authority

FID

Flight ID: Flight Plan call sign or aircraft
registration marking

Capability Report

Reports the available data and means by
which the transponder can report.

Pressure Altitude

Up to 35 000 ft in 25 ft increments

Flight Status

in-flight / on-ground

Mode S Enhanced Surveillance

Level 2es

Comm-A / Comm-B: 56/112-Bit-Messages

SI-capability

Summary of Contents for TRT800H-OLED



















































Search results

Summary of Contents for TRT800H-OLED

Reviews:

Related manuals for TRT800H-OLED

Brands by name

Popular brands

F.u.n.k.e. TRT800H-OLED, Operation And Installation

Search results

Summary of Contents for TRT800H-OLED

Reviews:

Related manuals for TRT800H-OLED

Brands by name

Popular brands