F.F. Group HG 2000 EASY, Original Instructions Manual

Page: 7 / 36

English | 7
www.ffgroup-tools.com
•
Do not strip metal window frames, as
the heat may be conducted onto the
glass and crack it. When stripping oth-
er window frames, use the glass pro-
tection nozzle.
•
Do not keep the tool directed at one
spot too long to prevent igniting the
surface.
•
Avoid collecting paint on the scraper
accessory, as it may ignite. If necessary,
carefully remove paint debris from the
scraper accessory using a knife.
8.4 Stationary use
This tool can also be used in stationary mode.
•
Place the tool onto the workbench.
•
Secure the cable to prevent pulling the tool off
the workbench.
•
Carefully switch the tool on.
Make sure that the nozzle always points
away from you and any bystanders.
Make sure not to drop anything into the
nozzle.
8.5 Cooling down
The nozzle and accessory become very hot during use.
Let them cool down before attempting to move or
store the tool.
•
To reduce the cooling time, switch the tool on at
the lowest air temperature setting and let it run
for a few minutes.
•
Switch the tool off and let it cool down for at least
30 minutes.
9 MAINTENANCE AND CLEANING
Attention! Before performing any work
on the equipment, pull the power plug.
9.1 Maintenance
Your Power Tool has been designed to operate
over a long period of time with a minimum of main-
tenance. Continuous satisfactory operation de-
pends upon proper tool care and regular cleaning.
9.2 Lubrication
Your power tool requires no additional lubrication.
9.3 Cleaning
Keep the ventilation slots clear and regularly clean
the housing with a soft cloth.
9.4 Cleaning
•
Keep the ventilation slots of the machine clean to
prevent overheating of the engine.
•
Regularly clean the machine housing with a soft
cloth, preferably after each use.
•
Keep the ventilation slots free from dust and dirt.
•
If the dirt does not come off use a soft cloth
moistened with soapy water.
Never use solvents such as petrol, alco-
hol, ammonia water, etc. These solvents
may damage the plastic parts.
10 TECHNICAL DATA
11 WARRANTY
•
This product is warranted in accordance with the
legal/country specific regulations, effective from
the date of purchase by the first user.
•
This warranty covers all material or production flaws.
It does not include: defective parts subject to normal
wear & tear, such as bearings, brushes, cables, plugs
or accessories such as drills, drill bits, saw blades etc.;
damage or defects resulting from abuse, accidents or
alterations; nor the costs for transport.
•
We reserve the right to reject any claim where the
purchase cannot be verified or when it is clear that
the product has not been properly maintained.
(Clean ventilation slots, carbon brushers serviced
regularly, …)
•
Your purchase receipt must be kept as proof of
date of purchase.
•
Your appliance must be returned un-dismantled to
your dealer in an acceptably clean state, accompa-
nied by your proof of purchase.
12 ENVIRONMENT
Should your appliance need replace-
ment after extended use, do not dis-
card it with the household rubbish but
dispose of it in an environmentally safe
way. Waste produced by electrical ma-
chine items should not be handled like
normal household rubbish. Please re-
cycle where facilities exist. Check with
your Local Authority or retailer for recy-
cling advice.
13. DECLARATION OF CONFORMITY
•
We declare under our sole responsibility that this
product is in conformity with the following stan-
dards or standardized documents: EN 60335-2-45,
EN 60335-1, EN 62233, ΕΝ 55014-1, EN 55014-2,
ΕΝ 61000-3-2, EN 61000-3-3, in accordance with
the provisions of the directives 2014/35/EU,
2014/30/EU
•
Technical file at:
FF GROUP TOOL INDUSTRIES S.A.,
19300 Aspropyrgos-Greece
Loudovikos Tsirigiotis
Operations & Engineering
FF GROUP TOOL INDUSTRIES S.A.,
19300 Aspropyrgos-Greece. 20/12/2017
Article number 41350
Voltage 230 V ~ 50HZ
Power supply 2000 W
Air temperature
/ Flow
I 50-450 o C; 250L/min
II 90-600
o
C; 500L/min