background image

13

14

Troubleshooting

Scenario 1

After the installation is complete and the batteries are in
place, none of the buttons are responsive. 
(No sound, and no backlight)  

Cause : Issues with batteries or the wiring.
Solution : Replace the batteries or make sure the batteries are installed
                correctly. Please check whether the cable from the interior lock
                unit is connected correctly.

Scenario 2

 the programming code while 

, the error message 

 after pressing the

confirm button. 
(The light blinks three times with three short beeps.)

Cause : Function setup 

 locked. 

Solution : Unlock the door by turning the turn-piece from the interior lock
                unit or with a key from the exterior.

When entering

setup of other

functions

appears

with the door

Temporarily 

 user codes

disable

Use one-time user code

Instruction : When all user codes are temporarily 

 all electronic functions will

                    be temporarily 

 as well. The door must be locked or unlocked

                    manually with the key. To restore user code functions, please
                    repeat the setup process for “Temporarily 

user code”.

disabled,

disabled

disable 

Enter

new UC

Restore factory default

Instruction : After removing the batteries, touch the keypads for three seconds and
                   re-install the batteries.
                   When the numbers 2, 5, 8, 0 are displayed on the keypad, press the
                   four numbers in any order until all numbers disappear.

8

9

Instruction : the timer can be set from 10 to 99 seconds.

Automatic lockup timer

6

Scenario 3

The door will not lock after pressing the      button because
the lever was turned before the motor had finished operating.

Cause : The lever or the knob is turned too early while the motor is not yet
             operating.
Solution : Wait for the end of the motor operating sound(the keypad light is
                off), and then press the     button again to execute the lockup
                function. 

■  
■  
    

PC (Programming code)

UC (User code)

Confirm button

Enter PC

Enter PC

Enter PC

Enter a two-digit
number (10

99)

Instruction : Once this user code is entered and used, it 

 and unable

                    to open the door again. However, the same one-time user code can
                    be set again.

is disabled

Summary of Contents for PT2Q0S10










Reviews: