EYEVAC BILINGUAL:Layout 1 1/10/10 5:08 AM Page 4
CLEANING THE MICRO EXHAUST FILTER HOLDER
1. The Micro Exhaust Filter Holder slides up and out of its housing on the side of the unit.
2. Gently pull the Filter out of the Filter Holder. (See Figure 4)
3. Tap Filter gently against trash container to free and eliminate excess dirt and debris. (See Figure 5)
4. To clean the Filter, wash in mild soap and water; rinse and dry thoroughly before using the unit.
5. If a new Filter is needed, replace with standard HEPA HF4 filter cartridges. Make sure that it fits snugly in the Filter
Holder. Replacement Filters are available through the Customer Service Department.
6. Slide the Holder back into the unit with the Filter facing outwards.
IMPORTANT! NEVER OPERATE EYE-VAC HOME WITHOUT THE MICRO EXHAUST FILTER AND FILTER HOLDER
PROPERLY IN PLACE.
CLEANING THE COLLECTION BIN
The Collection Bin should be washed periodically.
1. Wash the Bin in warm water using a mild soap. Avoid harsh or abrasive cleaners or sponges. Rinse thoroughly.
TO AVOID DAMAGE, DO NOT PLACE COLLECTION BIN IN THE DISHWASHER.
2. Let it air dry. Make sure the Collection Bin is completely dry before putting it back into the EYE-VAC PROFES-
SIONAL.
3. Insert the assembled Collection Bin following the instructions outlined in the USER MAINTENANCE
INSTRUCTIONS on page 3.
IMPORTANT NOTES
Other than cleaning the Dirt Filter and replacing the Micro Exhaust Filter Holder, as described in this Owner’s Manual,
this Automatic Vacuuming Dust Bin is not user serviceable. There are no user serviceable parts inside the unit.
Servicing by our Authorized Service Center is required to avoid damage to internal components.
STORAGE
1. Unplug unit and clean Collection Bin and all Filters before storing.
2. Store EYE-VAC HOME indoors, in a clean, dry place.
3. Never store EYE-VAC HOME while it is still plugged in. Never wrap cord tightly around the appliance, use the Cord
Storage area on the back of the EYE-VAC HOME unit. Do not put any stress on the cord where it enters the unit, as it
could cause the cord to wear and break.
WARNING! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT USE OUTDOORS OR ON WET SURFACES.
TROUBLE SHOOTING
Problem
Possible cause
Possible Solution
EYE-VAC HOME
won't run
1.Not firmly plugged in 2.Unit is
in OFF position 3.Dirt filter is not
in position 4.No power in wall
plug 5.Blown house fuse or
tripped circuit breaker
1.Plug in firmly 2.Turn control dial to MAN or AUTO
position 3.Re-attach collection bin lid to top of collection
bin 4.Check house fuse or circuit breaker 5.Have a
qualified licensed electrician replace house fuse or reset
circuit breaker
Does not pick up debris
1.Dirt inlet is blocked 2.Container
is full 3.Debris may be too large
for inlet
First. Turn control dial to OFF position 1.Clean path of
dirt inlet 2.Empty collection bin 3.Clear large debris
EYE-VAC sensors do not activate 1.Unit is not in AUTO mode
1.Turn control dial to AUTO position
Suction is not strong
1.Filters may be dirty
1. Turn control dial to the OFF position 2. Clean Dirt filter
or Micro Exhaust filters when needed.
Status indicator light blinking
1.Eye-Vac sensors have been shut
off for 30 seconds which caused
power to the motor to be shut off
1. Turn control dial to the OFF position 2.Check dirt
filter and micro exhaust filters to ensure they are
clean.
Collection Bin Indicator Light is
ON
1.Collection bin is full
1. Empty the Collection Bin; 2.Clean all dirt filters
Debris at inlet before unit is
powered on
1.Turn control dial to the MANUAL position
2. Activate unit manually
4
