Hand router and template
Recommended method
— use the 7" TouchLink Pro and TouchLink routing template, part
number 70-980-01, which is available at
www.extron.com
. Follow the instructions provided in
the
Routing Template User Guide
, available at
www.extron.com
.
NOTE:
The metal router guide must be purchased separately. It is reusable and should not
be discarded when the installation is complete.
USE
R AC
CES
S
EXTR
ON E
LEC
TRO
NICS
TLP 7
10C
V RO
UTE
R GU
IDE -
ALL
MO
DELS
STAN
DAR
D
0.625
IN O
UTS
IDE D
IAM
ETER
GUID
E BU
SHIN
G
0.500
IN C
UT D
IAM
ETER
STR
AIGH
T RO
UTE
R BIT
MET
RIC
16 M
M O
UTS
IDE D
IAM
ETER
GUID
E BU
SHIN
G
12 M
M O
R 12
.7 M
M C
UT D
IAM
ETER
STR
AIGH
T RO
UTE
R BIT
AND
A
Figure 5.
Using a Hand Router
CNC wood router
Recommended method
— if using a CNC router, enter the correct dimensions for the
TLP Pro 725C:
8.90 +0.00/-0.02 inches W x 7.1 +0.00/-0.02 inches D
226 +0.00/-0.5 mm W x 180 +0.00/-0.5 mm D
NOTE:
The underlined dimension is the connector or AAP access side for the unit.
Reciprocating saw or jigsaw
Acceptable method
— if using a reciprocating saw or jigsaw, make sure to use the paper
cutout template for the TLP Pro 725C. The template is available at
www.extron.com
.
Cut-
Out
Tem
pla
te fo
r th
e Ex
tron
TLP
Pro
720
C and
TLP
Pro
725
C
1.
Con
firm
th
e pr
odu
ct t
o be
ins
tal
led.
2.
Dou
ble
-ch
eck
th
e pr
int
se
ttings
,
befo
re
ing
, a
nd
mak
e s
ure
the
pa
ge
is
not
sc
ale
d.
3.
R
em
ove
th
e su
rfa
ce
cut-out
are
a
(gr
ay)
fr
om
the
te
mpl
ate
by
cut
tin
g
along
the
re
d li
ne.
DO
N
OT CU
T th
e gr
ay
dot
ted
line
s.
4.
Mea
sure
the
cu
tou
t a
nd te
mpl
ate
.
Mak
e sure
th
e di
mens
ion
s a
re th
e
sam
e a
s thos
e sh
own
.
5.
Pla
ce
the
te
mpl
ate
and
mar
k th
e
pos
ition
on
the
m
oun
ting
su
rfa
ce
whe
re
the
R
WM
2
is
bein
g in
sta
lle
d.
6.
D
oub
le
che
ck
pos
itio
n an
d
dim
ens
ion
s, t
hen
cut
th
e o
peni
ng
in th
e wa
ll.
68-21
79-
02 R
ev.
B
Trim
Ri
ng
Oute
r E
dge
(Do
not
cu
t th
is lin
e.)
Page
si
ze:
11"
x 17
"
Prin
t sc
ale
1:1
Do n
ot s
hrink
.
User
Acces
s
User
A
cce
ss
R =
0.
25"
(6
.4
mm
)
7.1
0"
(18
0 m
m)
8.9
0"
(22
6 m
m)
+ 0
.00
" (0
.00
cm
)
- 0
.02
" (0
.05
cm
)
SU
RFA
CE
CUT
-OU
T
ARE
A
Trim
R
ing
Lip
Widt
h =
0.
325
" (8
.3
mm
)
Trim
R
ing
O
Trim
r E
dge
r E
dg
er E
d
ter E
d
ute
rE
(Do
not
cu
t
(Do
his
line
.
his
l
his
li
this
li
this
l
th
is
)
Figure 6.
Using a Reciprocating Saw or Jigsaw
Running Cables
Run a LAN/PoE cable, all cables necessary to support the AC connector, the cables stored in the
enclosure, and all planned AAP connectors. They should be run below the table and through the
hole that was cut in the previous step.
ATTENTION:
•
Do not power on the touchpanels or control processors until you have read the
Attention
about Power over Ethernet (PoE) power supplies (see page 17).
•
Ne branchez pas les écrans tactiles ou les processeurs de contrôle avant d’avoir lu la
mise en garde
sur les sources d’alimentation via Ethernet (PoE) (voir page 17).
Leave enough slack to connect the cables before the enclosure is installed in the table.
TLP Pro 725C Series Touchpanels • Mounting
10
